我々の承諾だけでなく、お客様に最も全面的で最高のサービスを提供します。Ciscoの350-401試験問題の購入の前にあなたの無料の試しから、購入の後での一年間の無料更新まで我々はあなたのCiscoの350-401試験問題試験に一番信頼できるヘルプを提供します。Ciscoの350-401試験問題試験に失敗しても、我々はあなたの経済損失を減少するために全額で返金します。 NewValidDumpsがもっと早くCiscoの350-401試験問題認証試験に合格させるサイトで、Ciscoの350-401試験問題「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験についての問題集が市場にどんどん湧いてきます。NewValidDumpsを選択したら、成功をとりましょう。 社会と経済の発展につれて、多くの人はIT技術を勉強します。

CCNP Enterprise 350-401 これも現代社会が圧力に満ちている一つの反映です。

Cisco 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)試験問題「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験に合格することが簡単ではなくて、Cisco 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)試験問題証明書は君にとってはIT業界に入るの一つの手づるになるかもしれません。 Ciscoの350-401 試験時間認定試験を受験するために準備をしているあなたは、NewValidDumpsという成功できるチャンスを掴みましたか。NewValidDumpsの350-401 試験時間問題集はあなたが楽に試験に合格する保障です。

今の社会の中で、ネット上で訓練は普及して、弊社は試験問題集を提供する多くのネットの一つでございます。NewValidDumpsが提供したのオンライン商品がIT業界では品質の高い学習資料、受験生の必要が満足できるサイトでございます。

Cisco 350-401試験問題 - 私の夢は最高のIT専門家になることです。

NewValidDumpsのCiscoの350-401試験問題試験トレーニング資料はIT認証試験を受ける全ての受験生が試験に合格することを助けるもので、受験生からの良い評価をたくさんもらいました。NewValidDumpsを選ぶのは成功を選ぶのに等しいです。もしNewValidDumpsのCiscoの350-401試験問題試験トレーニング資料を購入した後、学習教材は問題があれば、或いは試験に不合格になる場合は、私たちが全額返金することを保証いたしますし、私たちは一年間で無料更新サービスを提供することもできます。

IT業種で仕事しているあなたは、夢を達成するためにどんな方法を利用するつもりですか。実際には、IT認定試験を受験して認証資格を取るのは一つの良い方法です。

350-401 PDF DEMO:

QUESTION NO: 1
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 3
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 4
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 5
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D

あなたの利用するCiscoのSAP C_ARSCC_2404ソフトが最新版のを保証するために、一年間の無料更新を提供します。 NewValidDumpsのVMware 250-589教材を購入したら、あなたは一年間の無料アップデートサービスを取得しました。 CiscoのCisco 100-160試験を準備しているあなたに試験に合格させるために、我々NewValidDumpsは模擬試験ソフトを更新し続けています。 Microsoft DP-300-KR - もちろんありますよ。 支払ってから、あなたは直ちにCiscoのMicrosoft PL-900-KR試験の資料をダウンロードすることができ、その後の一年間でCiscoのMicrosoft PL-900-KR試験ソフトが更新されたら、我々はあなたを通知します。

Updated: May 28, 2022