NewValidDumpsは同業の中でそんなに良い地位を取るの原因は弊社のかなり正確な試験の練習問題と解答そえに迅速の更新で、このようにとても良い成績がとられています。そして、弊社が提供した問題集を安心で使用して、試験を安心で受けて、君のCisco 350-401全真模擬試験認証試験の１００％の合格率を保証しますす。NewValidDumpsにたくさんのIT専門人士がいって、弊社の問題集に社会のITエリートが認定されて、弊社の問題集は試験の大幅カーバして、合格率が１００％にまで達します。 こうして、君は安心で試験の準備を行ってください。弊社の資料を使って、１００％に合格を保証いたします。 Ciscoの350-401全真模擬試験試験に合格することは容易なことではなくて、良い訓練ツールは成功の保証でNewValidDumpsは君の試験の問題を準備してしまいました。

CCNP Enterprise 350-401 弊社は君の試験の１００％合格率を保証いたします。

CCNP Enterprise 350-401全真模擬試験 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) あなたはいつでもサブスクリプションの期間を延長することができますから、より多くの時間を取って充分に試験を準備できます。 もし失敗したら、全額で返金を保証いたします。NewValidDumpsの問題集はIT専門家がCiscoの350-401 ウェブトレーニング「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験について自分の知識と経験を利用して研究したものでございます。

Ciscoの350-401全真模擬試験認定試験に受かるのはあなたの技能を検証することだけでなく、あなたの専門知識を証明できて、上司は無駄にあなたを雇うことはしないことの証明書です。当面、IT業界でCiscoの350-401全真模擬試験認定試験の信頼できるソースが必要です。NewValidDumpsはとても良い選択で、350-401全真模擬試験の試験を最も短い時間に縮められますから、あなたの費用とエネルギーを節約することができます。

Cisco 350-401全真模擬試験 - NewValidDumpsは君にとってベストな選択になります。

人生のチャンスを掴むことができる人は殆ど成功している人です。ですから、ぜひNewValidDumpsというチャンスを掴んでください。NewValidDumpsのCiscoの350-401全真模擬試験試験トレーニング資料はあなたがCiscoの350-401全真模擬試験認定試験に合格することを助けます。この認証を持っていたら、あなたは自分の夢を実現できます。そうすると人生には意義があります。

NewValidDumpsのCiscoの350-401全真模擬試験試験トレーニング資料は試験問題と解答を含まれて、豊富な経験を持っているIT業種の専門家が長年の研究を通じて作成したものです。その権威性は言うまでもありません。

350-401 PDF DEMO:

QUESTION NO: 1
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 2
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 4
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D

QUESTION NO: 5
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

Huawei H12-831_V1.0-ENU - 信じないでしょうか。 Microsoft PL-500-CN - 時間とお金の集まりより正しい方法がもっと大切です。 Amazon SAA-C03-JPN - しかし、これは本当のことですよ。 CiscoのJuniper JN0-223試験を準備しているあなたに試験に合格させるために、我々NewValidDumpsは模擬試験ソフトを更新し続けています。 H3C GB0-343 - では、どんな参考書は選べる価値を持っていますか。

Updated: May 28, 2022