彼らはNewValidDumpsの問題集が有効なこと確認しました。NewValidDumpsが提供しておりますのは専門家チームの研究した問題と真題で弊社の高い名誉はたぶり信頼をうけられます。安心で弊社の商品を使うために無料なサンブルをダウンロードしてください。 競争力が激しい社会に当たり、我々NewValidDumpsは多くの受験生の中で大人気があるのは受験生の立場からCisco　350-401サンプル問題集試験資料をリリースすることです。たとえば、ベストセラーのCisco　350-401サンプル問題集問題集は過去のデータを分析して作成ます。 NewValidDumpsは専門家チームが自分の知識と経験をを利用してCiscoの350-401サンプル問題集「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験の問題集を研究したものでございます。

350-401サンプル問題集問題集を利用して試験に合格できます。

CCNP Enterprise 350-401サンプル問題集 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) NewValidDumps はIT業界に認定試験大綱の主要なサプライヤーとして、専門家は一緻して品質の高い商品を開発し続けています。 NewValidDumpsは同業の中でそんなに良い地位を取るの原因は弊社のかなり正確な試験の練習問題と解答そえに迅速の更新で、このようにとても良い成績がとられています。そして、弊社が提供した問題集を安心で使用して、試験を安心で受けて、君のCisco 350-401 真実試験認証試験の１００％の合格率を保証しますす。

NewValidDumpsの専門家チームは彼らの経験と知識を利用して長年の研究をわたって多くの人は待ちに待ったCiscoの350-401サンプル問題集「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験について教育資料が完成してから、大変にお客様に歓迎されます。NewValidDumpsの模擬試験は真実の試験問題はとても似ている専門家チームの勤労の結果としてとても値打ちがあります。

Cisco 350-401サンプル問題集 - あなたは最高のトレーニング資料を手に入れました。

近年、IT領域で競争がますます激しくなります。IT認証は同業種の欠くことができないものになりました。あなたはキャリアで良い昇進のチャンスを持ちたいのなら、NewValidDumpsのCiscoの350-401サンプル問題集「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」試験トレーニング資料を利用してCiscoの認証の証明書を取ることは良い方法です。現在、Ciscoの350-401サンプル問題集認定試験に受かりたいIT専門人員がたくさんいます。NewValidDumpsの試験トレーニング資料はCiscoの350-401サンプル問題集認定試験の１００パーセントの合格率を保証します。

何ですか。自信を持っていないから350-401サンプル問題集試験を受けるのは無理ですか。

350-401 PDF DEMO:

QUESTION NO: 1
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 4
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").

QUESTION NO: 5
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

NewValidDumpsのCiscoのCisco 010-151J試験トレーニング資料は豊富な知識と経験を持っているIT専門家に研究された成果で、正確度がとても高いです。 それは NewValidDumpsのMicrosoft PL-900J問題集には実際の試験に出題される可能性がある問題をすべて含んでいて、しかもあなたをよりよく問題を理解させるように詳しい解析を与えますから。 NewValidDumpsのSAP C_SAC_2421問題集の合格率が100%に達することも数え切れない受験生に証明された事実です。 HashiCorp Terraform-Associate-003 - 不思議でしょう。 Microsoft AZ-204J認定試験に合格することは難しいようですね。

Updated: May 28, 2022