NewValidDumpsのCiscoの350-401試験問題試験トレーニング資料はインターネットでの全てのトレーニング資料のリーダーです。NewValidDumpsはあなたが首尾よく試験に合格することを助けるだけでなく、あなたの知識と技能を向上させることもできます。あなたが自分のキャリアでの異なる条件で自身の利点を発揮することを助けられます。 我々社はCisco　350-401試験問題試験に準備するあなたに怖さを取り除き、正確の方法と問題集を提供できます。ご購入の前後において、いつまでもあなたにヘルプを与えられます。 試験の準備をするためにNewValidDumpsのCiscoの350-401試験問題試験トレーニング資料を買うのは冒険的行為と思ったとしたら、あなたの人生の全てが冒険なことになります。

CCNP Enterprise 350-401 早速買いに行きましょう。

NewValidDumpsのシニア専門家チームはCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)試験問題試験に対してトレーニング教材を研究できました。 NewValidDumpsのCiscoの350-401 試験資料試験トレーニング資料はCiscoの350-401 試験資料認定試験を準備するのリーダーです。NewValidDumpsの Ciscoの350-401 試験資料試験トレーニング資料は高度に認証されたIT領域の専門家の経験と創造を含めているものです。

Ciscoの350-401試験問題は専門知識と情報技術の検査として認証試験で、NewValidDumpsはあなたに一日早くCiscoの認証試験に合格させて、多くの人が大量の時間とエネルギーを費やしても無駄になりました。NewValidDumpsにその問題が心配でなく、わずか20時間と少ないお金をを使って楽に試験に合格することができます。NewValidDumpsは君に対して特別の訓練を提供しています。

Cisco 350-401試験問題 - NewValidDumpsを選択したら、成功をとりましょう。

社会と経済の発展につれて、多くの人はIT技術を勉強します。なぜならば、IT職員にとって、Ciscoの350-401試験問題資格証明書があるのは肝心な指標であると言えます。自分の能力を証明するために、350-401試験問題試験に合格するのは不可欠なことです。弊社の350-401試験問題真題を入手して、試験に合格する可能性が大きくなります。

NewValidDumpsの勉強資料を手に入れたら、指示に従えば 350-401試験問題認定試験に受かることはたやすくなります。受験生の皆様にもっと多くの助けを差し上げるために、NewValidDumps のCiscoの350-401試験問題トレーニング資料はインターネットであなたの緊張を解消することができます。

350-401 PDF DEMO:

QUESTION NO: 1
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 3
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 4
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 5
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D

Snowflake COF-C02 - 我々NewValidDumpsは一番行き届いたアフタサービスを提供します。 当面、IT業界でCiscoのFortinet FCSS_SASE_AD-24認定試験の信頼できるソースが必要です。 我々社サイトのCisco　NFPA CFI-I問題庫は最新かつ最完備な勉強資料を有して、あなたに高品質のサービスを提供するのはNFPA CFI-I資格認定試験の成功にとって唯一の選択です。 SAP C-S4CPR-2408 - 皆さんは節約した時間とエネルギーを利用してもっと多くの金銭を稼ぐことができます。 あなたは無料でSalesforce CRT-403復習教材をダウンロードしたいですか？もちろん、回答ははいです。

Updated: May 28, 2022