現在IT技術会社に通勤しているあなたは、Ciscoの350-401復習問題集試験認定を取得しましたか？350-401復習問題集試験認定は給料の増加とジョブのプロモーションに役立ちます。短時間で350-401復習問題集試験に一発合格したいなら、我々社のCiscoの350-401復習問題集資料を参考しましょう。また、350-401復習問題集問題集に疑問があると、メールで問い合わせてください。 問題集に含まれているものは実際試験の問題を全部カバーすることができますから、あなたが一回で成功することを保証できます。NewValidDumpsはIT認定試験の350-401復習問題集問題集を提供して皆さんを助けるウエブサイトです。 だから、我々社は力の限りで弊社のCisco　350-401復習問題集試験資料を改善し、改革の変更に応じて更新します。

CCNP Enterprise 350-401 早くNewValidDumpsの問題集を君の手に入れましょう。

我々NewValidDumpsが自分のソフトに自信を持つのは我々のCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)復習問題集ソフトでCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)復習問題集試験に参加する皆様は良い成績を取りましたから。 君が後悔しないようにもっと少ないお金を使って大きな良い成果を取得するためにNewValidDumpsを選択してください。NewValidDumpsはまた一年間に無料なサービスを更新いたします。

試験に合格してからあなたがよりよい仕事と給料がもらえるかもしれません。Ciscoの350-401復習問題集試験は国際的に認可られます。これがあったら、よい高い職位の通行証を持っているようです。

Cisco 350-401復習問題集 - NewValidDumpsには専門的なエリート団体があります。

我々のNewValidDumpsサイトは一番高質量の350-401復習問題集試験資料と行き届いたアフタサービスを提供して協力します。Cisco　350-401復習問題集問題集は試験の範囲を広くカバーして、試験の通過率は高いです。他のサイトと比較して、我が社の350-401復習問題集試験問題集を購買すると決定します。商品の税金について、この問題を心配できません。顧客の利益を保証するために、税金は弊社の方で支払います。

試験の目標が変わる限り、あるいは我々の勉強資料が変わる限り、すぐに更新して差し上げます。あなたのニーズをよく知っていていますから、あなたに試験に合格する自信を与えます。

350-401 PDF DEMO:

QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 3
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

我々SiteName}を選択するとき、Cisco　HP HPE2-T38試験にうまく合格できるチャンスを捉えるといえます。 AVIXA CTS-D - 人生にはあまりにも多くの変化および未知の誘惑がありますから、まだ若いときに自分自身のために強固な基盤を築くべきです。 この問題集の合格率は高いので、多くのお客様からAmazon MLS-C01-KR問題集への好評をもらいました。 Microsoft AZ-204-KR - そうすると、あなたがいつでも最新バージョンの資料を持っていることが保証されます。 それは受験者の中で、PMI PMO-CP試験参考書が人気がある原因です。

Updated: May 28, 2022