Ciscoの350-401資格復習テキストの認定試験に合格すれば、就職機会が多くなります。この試験に合格すれば君の専門知識がとても強いを証明し得ます。Ciscoの350-401資格復習テキストの認定試験は君の実力を考察するテストでございます。 弊社の専門家たちのCiscoの350-401資格復習テキスト試験への研究はCiscoの350-401資格復習テキストソフトの高効率に保障があります。我々のデモを無料でやってみよう。 NewValidDumpsは君のために良い訓練ツールを提供し、君のCisco認証試に高品質の参考資料を提供しいたします。

その中で、350-401資格復習テキスト認定試験は最も重要な一つです。

あなたはインターネットでCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)資格復習テキスト認証試験の練習問題と解答の試用版を無料でダウンロードしてください。 なぜなら、それはCiscoの350-401 過去問認定試験に関する必要なものを含まれるからです。NewValidDumpsを選んだら、あなたは簡単に認定試験に合格することができますし、あなたはITエリートたちの一人になることもできます。

もし弊社の商品が君にとっては何も役割にならなくて全額で返金いたいます。多くのIT者がCiscoの350-401資格復習テキスト認定試験を通してIT業界の中で良い就職機会を得たくて、生活水準も向上させたいです。でも多くの人が合格するために大量の時間とエネルギーをかかって、無駄になります。

Cisco 350-401資格復習テキスト - 恐い研究の中から逸することができます。

社会と経済の発展につれて、多くの人はIT技術を勉強します。なぜならば、IT職員にとって、Ciscoの350-401資格復習テキスト資格証明書があるのは肝心な指標であると言えます。自分の能力を証明するために、350-401資格復習テキスト試験に合格するのは不可欠なことです。弊社の350-401資格復習テキスト真題を入手して、試験に合格する可能性が大きくなります。

我々のトレーニング資料は実践の検証に合格したもので、資料の問題集が全面的で、価格が手頃ということを保証します。NewValidDumpsのトレーニング資料はあなたが試験の準備をしている知識をテストできて、一定の時間にあなたのパフォーマンスを評価することもできますから、あなたの成績と弱点を指示して、弱い点を改善して差し上げます。

350-401 PDF DEMO:

QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

VMware 2V0-32.22 - 我々NewValidDumpsは一番行き届いたアフタサービスを提供します。 Fortinet FCSS_SASE_AD-24 - 当社のトレーニングツールは定期的に更新しますから、常に変わっている試験の目標に従っています。 我々社サイトのCisco　AVIXA CTS-I問題庫は最新かつ最完備な勉強資料を有して、あなたに高品質のサービスを提供するのはAVIXA CTS-I資格認定試験の成功にとって唯一の選択です。 NewValidDumpsのCiscoのMicrosoft PL-900試験トレーニング資料はカバー率が高くて、更新のスピードも速くて、完全なトレーニング資料ですから、NewValidDumps を手に入れたら、全てのIT認証が恐くなくなります。 あなたは無料でServiceNow CSA-JPN復習教材をダウンロードしたいですか？もちろん、回答ははいです。

Updated: May 28, 2022