我々の承諾だけでなく、お客様に最も全面的で最高のサービスを提供します。Ciscoの350-401最新問題の購入の前にあなたの無料の試しから、購入の後での一年間の無料更新まで我々はあなたのCiscoの350-401最新問題試験に一番信頼できるヘルプを提供します。Ciscoの350-401最新問題試験に失敗しても、我々はあなたの経済損失を減少するために全額で返金します。 現在、Ciscoの350-401最新問題認定試験に受かりたいIT専門人員がたくさんいます。NewValidDumpsの試験トレーニング資料はCiscoの350-401最新問題認定試験の１００パーセントの合格率を保証します。 競争力が激しい社会において、IT仕事をする人は皆、我々NewValidDumpsの350-401最新問題を通して自らの幸せを筑く建筑士になれます。

CCNP Enterprise 350-401 NewValidDumpsは君にとってベストな選択になります。

350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)最新問題試験参考書はお客様の試験のために最も役に立つ商品だとも言えます。 NewValidDumpsのCiscoの350-401 資格復習テキスト試験トレーニング資料は試験問題と解答を含まれて、豊富な経験を持っているIT業種の専門家が長年の研究を通じて作成したものです。その権威性は言うまでもありません。

もし弊社の問題集を勉強してそれは簡単になります。弊社はオンラインサービスとアフターサービスとオンラインなどの全面方面を含めてます。オンラインサービスは研究資料模擬练習問題などで、アフターサービスはNewValidDumpsが最新の認定問題だけでなく、絶えずに問題集を更新しています。

Cisco 350-401最新問題 - 心はもはや空しくなく、生活を美しくなります。

Ciscoの350-401最新問題認定試験に合格するためにたくさん方法があって、非常に少ないの時間とお金を使いのは最高で、NewValidDumpsが対応性の訓練が提供いたします。

また、350-401最新問題問題集に疑問があると、メールで問い合わせてください。現在IT技術会社に通勤しているあなたは、Ciscoの350-401最新問題試験認定を取得しましたか？350-401最新問題試験認定は給料の増加とジョブのプロモーションに役立ちます。

350-401 PDF DEMO:

QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

NewValidDumpsが提供したCiscoのPRINCE2 PRINCE2-Agile-Practitioner試験問題と解答が真実の試験の練習問題と解答は最高の相似性があり、一年の無料オンラインの更新のサービスがあり、100%のパス率を保証して、もし試験に合格しないと、弊社は全額で返金いたします。 だから、我々社は力の限りで弊社のCisco　The Open Group OG0-093試験資料を改善し、改革の変更に応じて更新します。 Huawei H14-321_V1.0 - しかも、一年間の無料更新サービスを提供します。 あなたはISTQB CTAL-TA試験に不安を持っていますか？ISTQB CTAL-TA参考資料をご覧下さい。 NewValidDumps のCisco 010-151試験トレーニング資料は特別にデザインしてできるだけあなたの仕事の効率を改善するのソフトです。

Updated: May 28, 2022