IT業種の人たちは自分のIT夢を持っているのを信じています。Ciscoの350-401認定テキスト認定試験に合格することとか、より良い仕事を見つけることとか。NewValidDumpsは君のCiscoの350-401認定テキスト認定試験に合格するという夢を叶えるための存在です。 NewValidDumps を選択して１００％の合格率を確保することができて、もし試験に失敗したら、NewValidDumpsが全額で返金いたします。 我々NewValidDumpsのあなたに開発するCiscoの350-401認定テキストソフトはあなたの問題を解決することができます。

CCNP Enterprise 350-401 NewValidDumpsを選んだら、成功への扉を開きます。

だから、弊社の提供する350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)認定テキスト問題集を暗記すれば、きっと試験に合格できます。 そうすると、あなたがいつでも最新バージョンの資料を持っていることが保証されます。NewValidDumpsはあなたが試験に合格するのを助けることができるだけでなく、あなたは最新の知識を学ぶのを助けることもできます。

Cisco 350-401認定テキスト試験参考書は研究、製造、販売とサービスに取り組んでいます。また、独自の研究チームと専門家を持っています。そのため、350-401認定テキスト試験参考書に対して、お客様の新たな要求に迅速に対応できます。

Cisco 350-401認定テキスト - でも、この試験はそれほど簡単ではありません。

Ciscoの350-401認定テキスト認定試験に合格することはきっと君の職業生涯の輝い将来に大変役に立ちます。NewValidDumpsを選ぶなら、君がCiscoの350-401認定テキスト認定試験に合格するということできっと喜んでいます。NewValidDumpsのCiscoの350-401認定テキスト問題集を購入するなら、君がCiscoの350-401認定テキスト認定試験に合格する率は１００パーセントです。あなたはNewValidDumpsの学習教材を購入した後、私たちは一年間で無料更新サービスを提供することができます。

試験科目の変化によって、最新の試験の内容も更新いたします。NewValidDumpsのインターネットであなたに年24時間のオンライン顧客サービスを無料で提供して、もしあなたはNewValidDumpsに失敗したら、弊社が全額で返金いたします。

350-401 PDF DEMO:

QUESTION NO: 1
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 2
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 4
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D

QUESTION NO: 5
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

弊社のCiscoのAmazon AWS-Certified-Machine-Learning-Specialtyソフトを購入するのを決めるとき、我々は各方面であなたに保障を提供します。 Microsoft DP-203J - NewValidDumpsの商品はIT業界中で高品質で低価格で君の試験のために専門に研究したものでございます。 試験が更新されているうちに、我々はCiscoのHuawei H12-811_V1.0試験の資料を更新し続けています。 SAP C-TFG61-2405はCiscoの一つ重要な認証試験で多くのIT専門スタッフが認証される重要な試験です。 Microsoft DP-700 - 自分の幸せは自分で作るものだと思われます。

Updated: May 28, 2022