いま350-401日本語版サンプル試験に合格するショートカットを教えてあげますから。あなたを試験に一発合格させる素晴らしい350-401日本語版サンプル試験に関連する参考書が登場しますよ。それはNewValidDumpsの350-401日本語版サンプル問題集です。 数年以来IT認証試験のためのソフトを開発している我々NewValidDumpsチームは国際的に大好評を博しています。我々はCiscoの350-401日本語版サンプルのような重要な試験を準備しているあなたに一番全面的で有効なヘルプを提供します。 もし不合格になったら、私たちは全額返金することを保証します。

CCNP Enterprise 350-401 我々の誠意を信じてください。

もし無事に350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)日本語版サンプル試験に合格したら、あなたはもっと自信になって、更なる勇気でやりたいことをしています。 自分のIT業界での発展を希望したら、Ciscoの350-401 受験対策試験に合格する必要があります。Ciscoの350-401 受験対策試験はいくつ難しくても文句を言わないで、我々NewValidDumpsの提供する資料を通して、あなたはCiscoの350-401 受験対策試験に合格することができます。

また、我々NewValidDumpsは量豊かのCisco　350-401日本語版サンプル試験資料を提供しますし、ソフト版であなたにCisco　350-401日本語版サンプル試験の最も現実的な環境をシミュレートさせます。勉強中で、何の質問があると、メールで我々はあなたのためにすぐ解決します。心配はありませんし、一心不乱に試験復習に取り組んでいます。

Cisco 350-401日本語版サンプル - 弊社はあなた１００％合格率を保証いたします。

NewValidDumps を選択して１００％の合格率を確保することができて、もし試験に失敗したら、NewValidDumpsが全額で返金いたします。

NewValidDumpsはCiscoの350-401日本語版サンプル認定試験「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」に向けてもっともよい問題集を研究しています。もしほかのホームページに弊社みたいな問題集を見れば、あとでみ続けて、弊社の商品を盗作することとよくわかります。

350-401 PDF DEMO:

QUESTION NO: 1
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 3
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D

QUESTION NO: 4
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 5
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

Fortinet FCP_FWF_AD-7.4 - 早くNewValidDumpsの問題集を君の手に入れましょう。 Microsoft AZ-900 - NewValidDumpsの問題集は最大のお得だね！ Huawei H19-137_V1.0 - 君が後悔しないようにもっと少ないお金を使って大きな良い成果を取得するためにNewValidDumpsを選択してください。 Amazon DVA-C02-JPN - きっと試験に合格しますよ。 NewValidDumps のCiscoのMicrosoft MS-900問題集はシラバスに従って、それにMicrosoft MS-900認定試験の実際に従って、あなたがもっとも短い時間で最高かつ最新の情報をもらえるように、弊社はトレーニング資料を常にアップグレードしています。

Updated: May 28, 2022