周りの多くの人は全部Cisco　350-401基礎問題集資格認定試験にパースしまして、彼らはどのようにできましたか。今には、あなたにNewValidDumpsを教えさせていただけませんか。我々社サイトのCisco　350-401基礎問題集問題庫は最新かつ最完備な勉強資料を有して、あなたに高品質のサービスを提供するのは350-401基礎問題集資格認定試験の成功にとって唯一の選択です。 あなたが仕事を求める競争力を高めて、自分の技術レベルに合わせている技術職を取って、気楽にホワイトカラー労働者になって高い給料を取ることをお祈りします。NewValidDumpsがCiscoの350-401基礎問題集のサンプルの問題のダウンロードを提供して、あなはリスクフリーの購入のプロセスを体験することができます。 そうすれば、あなたは簡単に350-401基礎問題集復習教材のデモを無料でダウンロードできます。

CCNP Enterprise 350-401 最もよくて最新で資料を提供いたします。

CCNP Enterprise 350-401基礎問題集 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) 成功したいのですか。 Cisco 350-401 無料試験「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験に合格することが簡単ではなくて、Cisco 350-401 無料試験証明書は君にとってはIT業界に入るの一つの手づるになるかもしれません。しかし必ずしも大量の時間とエネルギーで復習しなくて、弊社が丹精にできあがった問題集を使って、試験なんて問題ではありません。

誰もが成功する可能性があって、大切なのは選択することです。成功した方法を見つけるだけで、失敗の言い訳をしないでください。Ciscoの350-401基礎問題集試験に受かるのは実際にそんなに難しいことではないです。

Cisco 350-401基礎問題集 - IT認定試験は様々あります。

Ciscoの350-401基礎問題集認定試験は実は技術専門家を認証する試験です。 Ciscoの350-401基礎問題集認定試験はIT人員が優れたキャリアを持つことを助けられます。優れたキャリアを持ったら、社会と国のために色々な利益を作ることができて、国の経済が継続的に発展していることを進められるようになります。全てのIT人員がそんなにられるとしたら、国はぜひ強くなります。NewValidDumpsのCiscoの350-401基礎問題集試験トレーニング資料はIT人員の皆さんがそんな目標を達成できるようにヘルプを提供して差し上げます。NewValidDumpsのCiscoの350-401基礎問題集試験トレーニング資料は１００パーセントの合格率を保証しますから、ためらわずに決断してNewValidDumpsを選びましょう。

非常に人気があるCiscoの認定試験の一つとして、この試験も大切です。しかし、試験の準備をよりよくできるために試験参考書を探しているときに、優秀な参考資料を見つけるのはたいへん難しいことがわかります。

350-401 PDF DEMO:

QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

Amazon AWS-Certified-Machine-Learning-Specialty-KR - それはあなたが夢を実現することを助けられます。 NewValidDumpsはCiscoのAmazon SOA-C02-KR問題集の正確性と高いカバー率を保証します。 SAP P_BTPA_2408 - あなたの夢は何ですか。 Microsoft AZ-700J - NewValidDumpsを選ぶなら、私たちは君の認定試験に合格するのを保証します。 NewValidDumpsのMicrosoft AZ-204教材を購入したら、あなたは一年間の無料アップデートサービスを取得しました。

Updated: May 28, 2022