NewValidDumpsの専門家チームが君の需要を満たすために自分の経験と知識を利用してCiscoの350-401模擬モード認定試験対策模擬テスト問題集が研究しました。模擬テスト問題集と真実の試験問題がよく似ています。一目でわかる最新の出題傾向でわかりやすい解説と充実の補充問題があります。 弊社の350-401模擬モード問題集を買う人は全部350-401模擬モード試験にいい成績で合格しました。弊社の350-401模擬モード問題集はIT業界で有名で、ブランドになっています。 NewValidDumpsのCiscoの350-401模擬モードの試験問題は同じシラバスに従って、実際のCiscoの350-401模擬モード認証試験にも従っています。

CCNP Enterprise 350-401 問題があったら気軽にお問いください、

NewValidDumpsの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)模擬モード問題集の合格率が100%に達することも数え切れない受験生に証明された事実です。 NewValidDumpsはCiscoの350-401 勉強時間認定試験に対して問題集を提供しておるサイトで、現場のCiscoの350-401 勉強時間試験問題と模擬試験問題集を含みます。ほかのホームページに弊社みたいな問題集を見れば、あとでみ続けて、弊社の商品を盗作することとよくわかります。

いま350-401模擬モード試験に合格するショートカットを教えてあげますから。あなたを試験に一発合格させる素晴らしい350-401模擬モード試験に関連する参考書が登場しますよ。それはNewValidDumpsの350-401模擬モード問題集です。

Cisco 350-401模擬モード - ここには、私たちは君の需要に応じます。

NewValidDumps のCiscoの350-401模擬モード問題集は最も徹底的で、最も正確で、かつアップ·ツー·デートなものです。当面の市場であなたに初めて困難を乗り越える信心を差し上げられるユニークなソフトです。Ciscoの350-401模擬モード認証試験は世界でどの国でも承認されて、すべての国が分け隔てをしないの試験です。NewValidDumps のCiscoの350-401模擬モード認証証明書はあなたが自分の知識と技能を高めることに助けになれることだけでなく、さまざまな条件であなたのキャリアを助けることもできます。NewValidDumps のCiscoの350-401模擬モード問題集を利用することをお勧めいたします。

うちのCiscoの350-401模擬モード試験トレーニング資料を購入する前に、NewValidDumpsのサイトで、一部分のフリーな試験問題と解答をダンロードでき、試用してみます。君がうちの学習教材を購入した後、私たちは一年間で無料更新サービスを提供することができます。

350-401 PDF DEMO:

QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

NewValidDumpsのCiscoのGoogle Professional-Machine-Learning-Engineer「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」トレーニング資料を利用したら、初めて試験を受けるあなたでも一回で試験に合格できることを保証します。 Symantec 250-580 - 我々の誠意を信じてください。 Microsoft PL-500 - NewValidDumpsを選ぶのは、成功を選ぶということになります。 自分のIT業界での発展を希望したら、CiscoのIAPP CIPP-US試験に合格する必要があります。 Salesforce DEX-403J - NewValidDumpsをクロックしたら、１００パーセントの成功を差し上げます。

Updated: May 28, 2022