NewValidDumpsを選られば、成功しましょう。わずか数年の中に、Cisco 350-401認定デベロッパー認定試験がたくさんの人の日常生活にとても大きい影響を与えています。簡単で順調にCisco 350-401認定デベロッパー認定試験を通すのは問題になりますが、NewValidDumpsはこの問題を解決できるよ。 Ciscoの350-401認定デベロッパーの認定試験に合格すれば、就職機会が多くなります。この試験に合格すれば君の専門知識がとても強いを証明し得ます。 弊社の勉強の商品を選んで、多くの時間とエネルギーを節約こともできます。

CCNP Enterprise 350-401 きっと君に失望させないと信じています。

CCNP Enterprise 350-401認定デベロッパー - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) それは受験者にとって重要な情報です。 我々は受験生の皆様により高いスピードを持っているかつ効率的なサービスを提供することにずっと力を尽くしていますから、あなたが貴重な時間を節約することに助けを差し上げます。NewValidDumps Ciscoの350-401 絶対合格試験問題集はあなたに問題と解答に含まれている大量なテストガイドを提供しています。

NewValidDumpsはきみのIT夢に向かって力になりますよ。NewValidDumpsは多種なIT認証試験を受ける方を正確な資料を提供者でございます。弊社の無料なサンプルを遠慮なくダウンロードしてください。

Cisco 350-401認定デベロッパー - これは多くの受験生に証明されたことです。

Ciscoの認証資格は最近ますます人気になっていますね。国際的に認可された資格として、Ciscoの認定試験を受ける人も多くなっています。その中で、350-401認定デベロッパー認定試験は最も重要な一つです。では、この試験に合格するためにどのように試験の準備をしているのですか。がむしゃらに試験に関連する知識を勉強しているのですか。それとも、効率が良い試験350-401認定デベロッパー参考書を使っているのですか。

Ciscoの350-401認定デベロッパー試験を受けることは私の人生の挑戦の一つです。でも大丈夫です。

350-401 PDF DEMO:

QUESTION NO: 1
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 3
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 4
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 5
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D

Cisco 200-201J - 早速買いに行きましょう。 これは間違いなくあなたが一番信頼できるSplunk SPLK-1002J試験に関連する資料です。 IBM C1000-138 - それは正確性が高くて、カバー率も広いです。 NewValidDumpsはあなたがAdobe AD0-E123認定試験に合格する保障ですから。 我々はあなたに提供するのは最新で一番全面的なCiscoのMicrosoft SC-400J問題集で、最も安全な購入保障で、最もタイムリーなCiscoのMicrosoft SC-400J試験のソフトウェアの更新です。

Updated: May 28, 2022