弊社のIT業で経験豊富な専門家たちが正確で、合理的なCisco 350-401模擬対策問題認証問題集を作り上げました。 弊社の勉強の商品を選んで、多くの時間とエネルギーを節約こともできます。 あなたの全部な需要を満たすためにいつも頑張ります。きみはCiscoの350-401模擬対策問題認定テストに合格するためにたくさんのルートを選択肢があります。 Ciscoの350-401模擬対策問題認定試験の合格証明書はあなたの仕事の上で更に一歩の昇進で生活条件が向上することが助けられます。

CCNP Enterprise 350-401 それは受験者にとって重要な情報です。

インターネットで時勢に遅れない350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)模擬対策問題勉強資料を提供するというサイトがあるかもしれませんが、NewValidDumpsはあなたに高品質かつ最新のCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)模擬対策問題トレーニング資料を提供するユニークなサイトです。 弊社の無料なサンプルを遠慮なくダウンロードしてください。君はまだCiscoの350-401 PDF問題サンプル認証試験を通じての大きい難度が悩んでいますか？ 君はまだCisco 350-401 PDF問題サンプル認証試験に合格するために寝食を忘れて頑張って復習しますか？ 早くてCisco 350-401 PDF問題サンプル認証試験を通りたいですか？NewValidDumpsを選択しましょう！

ためらわずに速くあなたのショッピングカートに入れてください。でないと、絶対後悔しますよ。NewValidDumpsが提供したCiscoの350-401模擬対策問題トレーニング資料を利用したら、Ciscoの350-401模擬対策問題認定試験に受かることはたやすくなります。

Cisco 350-401模擬対策問題 - 本当に皆様に極大なヘルプを差し上げますから。

IT認定試験の中でどんな試験を受けても、NewValidDumpsの350-401模擬対策問題試験参考資料はあなたに大きなヘルプを与えることができます。それは NewValidDumpsの350-401模擬対策問題問題集には実際の試験に出題される可能性がある問題をすべて含んでいて、しかもあなたをよりよく問題を理解させるように詳しい解析を与えますから。真剣にNewValidDumpsのCisco 350-401模擬対策問題問題集を勉強する限り、受験したい試験に楽に合格することができるということです。

NewValidDumpsは専門的なIT認証サイトで、成功率が１００パーセントです。これは多くの受験生に証明されたことです。

350-401 PDF DEMO:

QUESTION NO: 1
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 4
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D

QUESTION NO: 5
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

Fortinet NSE7_SDW-7.2 - Ciscoの認証資格は最近ますます人気になっていますね。 NewValidDumpsのCiscoのMicrosoft SC-400試験トレーニング資料を購入しましたから。 Huawei H40-121 - まだ何を待っていますか。 これは間違いなくあなたが一番信頼できるOracle 1z0-071試験に関連する資料です。 NewValidDumpsのCiscoのScrum PSPO-I試験トレーニング資料はCiscoのScrum PSPO-I認定試験を準備するのリーダーです。

Updated: May 28, 2022