我々社サイトのCisco　350-401難易度問題庫は最新かつ最完備な勉強資料を有して、あなたに高品質のサービスを提供するのは350-401難易度資格認定試験の成功にとって唯一の選択です。躊躇わなくて、NewValidDumpsサイト情報を早く了解して、あなたに試験合格を助かってあげますようにお願いいたします。周りの多くの人は全部Cisco　350-401難易度資格認定試験にパースしまして、彼らはどのようにできましたか。 我々の問題集によって、ほとんどの受験生は大方の人から見る大変なCisco　350-401難易度試験にうまく合格しました。この成功データは350-401難易度試験に準備する皆様にNewValidDumpsの350-401難易度問題集を勧める根拠とします。 あなたは無料で350-401難易度復習教材をダウンロードしたいですか？もちろん、回答ははいです。

CCNP Enterprise 350-401 でも、成功へのショートカットがを見つけました。

Ciscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)難易度認証試験はIT業界にとても重要な地位があることがみんなが、たやすくその証本をとることはではありません。 さて、はやく試験を申し込みましょう。NewValidDumpsはあなたを助けることができますから、心配する必要がないですよ。

弊社の資料があなたに練習を実践に移すチャンスを差し上げ、あなたはぜひCiscoの350-401難易度試験に合格して自分の目標を達成できます。NewValidDumps のCiscoの350-401難易度問題集は１００パーセント検証とテストを通過したもので、認定試験に合格する専門的な指導者です。NewValidDumps のCiscoの350-401難易度「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」練習問題集と解答は実践の検査に合格したソフトウェアで、最も受験生に合うトレーニングツールです。

Cisco 350-401難易度 - もちろんありますよ。

NewValidDumpsというサイトは世界的に知名度が高いです。それはNewValidDumpsが提供したIT業種のトレーニング資料の適用性が強いですから。それはNewValidDumpsのIT専門家が長い時間で研究した成果です。彼らは自分の知識と経験を活かして、絶え間なく発展しているIT業種の状況によってNewValidDumpsのCiscoの350-401難易度トレーニング資料を作成したのです。多くの受験生が利用してからとても良い結果を反映しました。もしあなたはIT認証試験に準備している一人でしたら、NewValidDumpsのCiscoの350-401難易度「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」トレーニング資料を選らんだほうがいいです。利用しないのならメリットが分からないですから、速く使ってみてください。

君がCiscoの350-401難易度問題集を購入したら、私たちは一年間で無料更新サービスを提供することができます。もしCiscoの350-401難易度問題集は問題があれば、或いは試験に不合格になる場合は、全額返金することを保証いたします。

350-401 PDF DEMO:

QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 4
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

OMG OMG-OCEB2-FUND100 - そうしたら、半分の労力で二倍の効果を得ることができます。 弊社のソフトを使用して、ほとんどのお客様は難しいと思われているCiscoのCisco 300-420試験に順調に剛角しました。 VMware 2V0-41.24-JPN - 本当の能力は実践で鍛えたもので、学歴と直接な関係がないです。 Microsoft AI-102-KR - これをよくできるために、我々は全日24時間のサービスを提供します。 SAP C_THR81_2405 - では、仕事に役に立つスキルをもっと身に付けましょう。

Updated: May 28, 2022