実際には、IT認定試験を受験して認証資格を取るのは一つの良い方法です。最近、Ciscoの350-401資格試験試験は非常に人気のある認定試験です。あなたもこの試験の認定資格を取得したいのですか。 我々は心からあなたが首尾よく試験に合格することを願っています。あなたに便利なオンラインサービスを提供して、Cisco 350-401資格試験試験問題についての全ての質問を解決して差し上げます。 たとえば350-401資格試験認定試験などです。
NewValidDumpsはCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)資格試験問題集の正確性と高いカバー率を保証します。 きっと望んでいるでしょう。では、常に自分自身をアップグレードする必要があります。
しかし、Ciscoの350-401資格試験認定試験に合格するという夢は、NewValidDumpsに対して、絶対に掴められます。NewValidDumpsは親切なサービスで、Ciscoの350-401資格試験問題集が質の良くて、Ciscoの350-401資格試験認定試験に合格する率も100パッセントになっています。NewValidDumpsを選ぶなら、私たちは君の認定試験に合格するのを保証します。
NewValidDumpsのCiscoの350-401資格試験試験トレーニング資料は豊富な経験を持っているIT専門家が研究したものです。君がCiscoの350-401資格試験問題集を購入したら、私たちは一年間で無料更新サービスを提供することができます。もしCiscoの350-401資格試験問題集は問題があれば、或いは試験に不合格になる場合は、全額返金することを保証いたします。
ご購入の後、我々はタイムリーにあなたにCiscoの350-401資格試験ソフトの更新情報を提供して、あなたの備考過程をリラクスにします。NewValidDumpsの発展は弊社の商品を利用してIT認証試験に合格した人々から得た動力です。
QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 3
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
弊社のNewValidDumpsはIT認定試験のソフトの一番信頼たるバンドになるという目標を達成するために、弊社はあなたに最新版のCiscoのAmazon Data-Engineer-Associate-KR試験問題集を提供いたします。 CiscoのMicrosoft DP-203-KR試験に参加するのを決めるとき、あなたは強い心を持っているのを証明します。 AACE International AACE-PSP - これをよくできるために、我々は全日24時間のサービスを提供します。 高質のCisco試験資料を持って、短い時間で気軽に試験に合格したいですか?そうしたら、我が社NewValidDumpsのHuawei H19-121_V1.0問題集をご覧にください。 あなたは各バーションのCiscoのCollege Admission CAST試験の資料をダウンロードしてみることができ、あなたに一番ふさわしいバーションを見つけることができます。
Updated: May 28, 2022
試験コード:350-401
試験名称:Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)
最近更新時間:2024-12-22
問題と解答:全 1282 問
Cisco 350-401 復習対策
ダウンロード
試験コード:350-401
試験名称:Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)
最近更新時間:2024-12-22
問題と解答:全 1282 問
Cisco 350-401 難易度受験料
ダウンロード
試験コード:350-401
試験名称:Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)
最近更新時間:2024-12-22
問題と解答:全 1282 問
Cisco 350-401 テストサンプル問題
ダウンロード