NewValidDumpsのCiscoの350-401日本語版サンプル試験トレーニング資料は今までがないIT認証のトレーニング資料ですから、NewValidDumpsを利用したら、あなたのキャリアは順調に進むことができるようになります。NewValidDumpsは専門的に IT認証試験に関する資料を提供するサイトで、１００パーセントの合格率を保証できます。それもほとんどの受験生はNewValidDumpsを選んだ理由です。 これは試験の準備をするために非常に効率的なツールですから。この問題集はあなたが少ない労力で最高の結果を取得することができます。 進歩を勇敢に追及する人生こそ素晴らしい人生です。

CCNP Enterprise 350-401 この問題集をミスすればあなたの大きな損失ですよ。

NewValidDumpsのCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)日本語版サンプル問題集を購入したら、私たちは君のために、一年間無料で更新サービスを提供することができます。 この参考書は短い時間で試験に十分に準備させ、そして楽に試験に合格させます。試験のためにあまりの時間と精力を無駄にしたくないなら、NewValidDumpsの350-401 復習時間問題集は間違いなくあなたに最もふさわしい選択です。

うちのCiscoの350-401日本語版サンプル試験トレーニング資料を購入する前に、NewValidDumpsのサイトで、一部分のフリーな試験問題と解答をダンロードでき、試用してみます。君がうちの学習教材を購入した後、私たちは一年間で無料更新サービスを提供することができます。NewValidDumpsのCiscoの350-401日本語版サンプル試験トレーニング資料は試験問題と解答を含まれて、豊富な経験を持っているIT業種の専門家が長年の研究を通じて作成したものです。

全力を尽くせば、Cisco 350-401日本語版サンプル試験の合格も可能となります。

NewValidDumpsはきみの貴重な時間を節約するだけでなく、 安心で順調に試験に合格するのを保証します。NewValidDumpsは専門のIT業界での評判が高くて、あなたがインターネットでNewValidDumpsの部分のCisco 350-401日本語版サンプル「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」資料を無料でダウンロードして、弊社の正確率を確認してください。弊社の商品が好きなのは弊社のたのしいです。

このほど、今のIT会社は多くのIT技術人材を急速に需要して、あなたはこのラッキーな人になりたいですか？Ciscoの350-401日本語版サンプル試験に参加するのはあなたに自身のレベルを高めさせるだけでなく、あなたがより良く就職し輝かしい未来を持っています。弊社NewValidDumpsはCiscoの350-401日本語版サンプル問題集を購入し勉強した後、あなたは350-401日本語版サンプル試験に合格することでできると信じています。

350-401 PDF DEMO:

QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 3
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

EC-COUNCIL 312-49v11 - NewValidDumps を選択して１００％の合格率を確保することができて、もし試験に失敗したら、NewValidDumpsが全額で返金いたします。 Microsoft AZ-305-KR - 一年間の無料更新と試験に合格しなくて全額返金も我々の誠のアフタサーブすでございます。 AVIXA CTS-I - そうしたらあなたはNewValidDumpsが用意した問題集にもっと自信があります。 Cisco　Microsoft AZ-500資格試験に参加する意向があれば、当社のNewValidDumpsから自分に相応しい受験対策解説集を選らんで、認定試験の学習教材として勉強します。 NewValidDumpsにIT業界のエリートのグループがあって、彼達は自分の経験と専門知識を使ってCisco Microsoft AI-900J認証試験に参加する方に対して問題集を研究続けています。

Updated: May 28, 2022