きみはCiscoの350-401学習範囲認定テストに合格するためにたくさんのルートを選択肢があります。NewValidDumpsは君のために良い訓練ツールを提供し、君のCisco認証試に高品質の参考資料を提供しいたします。あなたの全部な需要を満たすためにいつも頑張ります。 しかし、難しい試験といっても、試験を申し込んで受験する人が多くいます。なぜかと言うと、もちろん350-401学習範囲認定試験がとても大切な試験ですから。 NewValidDumpsの専門家チームがCiscoの350-401学習範囲認証試験に対して最新の短期有効なトレーニングプログラムを研究しました。

CCNP Enterprise 350-401 常々、時間とお金ばかり効果がないです。

NewValidDumpsのCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)学習範囲試験トレーニング資料はインターネットでの全てのトレーニング資料のリーダーです。 我々NewValidDumpsは350-401 過去問試験の難しさを減らないとは言え、試験準備の難しさを減ることができます。我々の提供する問題集を体験してから、あなたはCiscoの350-401 過去問試験に合格できる自信を持っています。

試験の準備をするためにNewValidDumpsのCiscoの350-401学習範囲試験トレーニング資料を買うのは冒険的行為と思ったとしたら、あなたの人生の全てが冒険なことになります。一番遠いところへ行った人はリスクを背負うことを恐れない人です。また、NewValidDumpsのCiscoの350-401学習範囲試験トレーニング資料が信頼できるのは多くの受験生に証明されたものです。

Cisco 350-401学習範囲 - 早速買いに行きましょう。

Cisco　350-401学習範囲資格認定はバッジのような存在で、あなたの所有する専業技術と能力を上司に直ちに知られさせます。次のジョブプロモーション、プロジェクタとチャンスを申し込むとき、Cisco　350-401学習範囲資格認定はライバルに先立つのを助け、あなたの大業を成し遂げられます。

NewValidDumpsのCiscoの350-401学習範囲試験トレーニング資料はCiscoの350-401学習範囲認定試験を準備するのリーダーです。NewValidDumpsの Ciscoの350-401学習範囲試験トレーニング資料は高度に認証されたIT領域の専門家の経験と創造を含めているものです。

350-401 PDF DEMO:

QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

あなたはAVIXA CTS-I試験に興味を持たれば、今から行動し、AVIXA CTS-I練習問題を買いましょう。 我々はあなたに提供するのは最新で一番全面的なCiscoのHP HPE2-B03問題集で、最も安全な購入保障で、最もタイムリーなCiscoのHP HPE2-B03試験のソフトウェアの更新です。 だから、AACE International AACE-PSP復習教材を買いました。 CiscoのGoogle Google-Workspace-Administrator試験に失敗しても、我々はあなたの経済損失を減少するために全額で返金します。 あなたはその他のCisco H3C GB0-372「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験に関するツールサイトでも見るかも知れませんが、弊社はIT業界の中で重要な地位があって、NewValidDumpsの問題集は君に100%で合格させることと君のキャリアに変らせることだけでなく一年間中で無料でサービスを提供することもできます。

Updated: May 28, 2022