NewValidDumpsの専門家チームがCiscoの350-401学習指導認証試験に対して最新の短期有効なトレーニングプログラムを研究しました。Ciscoの350-401学習指導「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験に参加者に対して30時間ぐらいの短期の育成訓練でらくらくに勉強しているうちに多くの知識を身につけられます。 当社の認定トレーニングの材料は、すぐに入手できます。当社のサイトは答案ダンプのリーディングプロバイダーで、あなたが利用したい最新かつ最正確の試験認定トレーニング材料、いわゆる試験問題と解答を提供しています。 きっと君に失望させないと信じています。

CCNP Enterprise 350-401 IT職員としてのあなたは切迫感を感じましたか。

それは NewValidDumpsの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)学習指導問題集には実際の試験に出題される可能性がある問題をすべて含んでいて、しかもあなたをよりよく問題を理解させるように詳しい解析を与えますから。 いかがですか。NewValidDumpsの問題集はあなたを試験の準備する時間を大量に節約させることができます。

Ciscoの認証資格は最近ますます人気になっていますね。国際的に認可された資格として、Ciscoの認定試験を受ける人も多くなっています。その中で、350-401学習指導認定試験は最も重要な一つです。

Cisco 350-401学習指導 - まだ何を待っていますか。

350-401学習指導認定試験は現在で本当に人気がある試験ですね。まだこの試験の認定資格を取っていないあなたも試験を受ける予定があるのでしょうか。確かに、これは困難な試験です。しかし、難しいといっても、高い点数を取って楽に試験に合格できないというわけではないです。では、まだ試験に合格するショートカットがわからないあなたは、受験のテクニックを知りたいですか。今教えてあげますよ。それはNewValidDumpsの350-401学習指導問題集を利用することです。

それは正確性が高くて、カバー率も広いです。あなたはNewValidDumpsの学習教材を購入した後、私たちは一年間で無料更新サービスを提供することができます。

350-401 PDF DEMO:

QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 2
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 5
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").

NewValidDumpsは最も安い値段で正確性の高いCiscoのGoogle Professional-Data-Engineer-JPN問題集を提供します。 我々はあなたに提供するのは最新で一番全面的なCiscoのCompTIA 220-1102J問題集で、最も安全な購入保障で、最もタイムリーなCiscoのCompTIA 220-1102J試験のソフトウェアの更新です。 GIAC GWEB - その権威性が高いと言えます。 CiscoのMicrosoft SC-200試験に失敗しても、我々はあなたの経済損失を減少するために全額で返金します。 Fortinet FCP_FGT_AD-7.4 - あなたはNewValidDumpsの学習教材を購入した後、私たちは一年間で無料更新サービスを提供することができます。

Updated: May 28, 2022