それぞれのIT認証試験を受ける受験生の身近な利益が保障できるために、NewValidDumpsは受験生のために特別に作成されたCiscoの350-401再テスト試験トレーニング資料を提供します。この資料はNewValidDumpsのIT専門家たちに特別に研究されたものです。彼らの成果はあなたが試験に合格することを助けるだけでなく、あなたにもっと美しい明日を与えることもできます。 NewValidDumpsはきみの貴重な時間を節約するだけでなく、 安心で順調に試験に合格するのを保証します。NewValidDumpsは専門のIT業界での評判が高くて、あなたがインターネットでNewValidDumpsの部分のCisco 350-401再テスト「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」資料を無料でダウンロードして、弊社の正確率を確認してください。 NewValidDumps的350-401再テスト問題集は絶対あなたがよく試験に準備して、しかも自分を向上させる一番良い選択です。

CCNP Enterprise 350-401 NewValidDumpsには専門的なエリート団体があります。

CCNP Enterprise 350-401再テスト - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) 資料の整理に悩んでいますか。 試験の目標が変わる限り、あるいは我々の勉強資料が変わる限り、すぐに更新して差し上げます。あなたのニーズをよく知っていていますから、あなたに試験に合格する自信を与えます。

成功の喜びは大きいです。我々は弊社のソフトを通してあなたにCiscoの350-401再テスト試験に合格する喜びを感じさせると希望しています。あなたの成功も我々NewValidDumpsの成功です。

Cisco 350-401再テスト - 正しい方法は大切です。

弊社の350-401再テスト問題集のメリットはいろいろな面で記述できます。価格はちょっと高いですが、350-401再テスト試験に最も有効な参考書です。350-401再テスト問題集は便利で、どこでもいつでも勉強できます。また、時間を節約でき、短い時間で勉強したら、350-401再テスト試験に参加できます。

できるだけ100％の通過率を保証使用にしています。NewValidDumpsは多くの受験生を助けて彼らにCiscoの350-401再テスト試験に合格させることができるのは我々専門的なチームがCiscoの350-401再テスト試験を研究して解答を詳しく分析しますから。

350-401 PDF DEMO:

QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 4
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

HP HPE0-J68 - あなたにとても良い指導を確保できて、試験に合格するのを助けって、NewValidDumpsからすぐにあなたの通行証をとります。 ただ、社会に入るIT卒業生たちは自分能力の不足で、SAP C_TS412_2021-JPN試験向けの仕事を探すのを悩んでいますか？それでは、弊社のCiscoのSAP C_TS412_2021-JPN練習問題を選んで実用能力を速く高め、自分を充実させます。 Amazon Data-Engineer-Associate-KR - 明日の成功のためにNewValidDumpsを選らばましょう。 NewValidDumpsのCisco　Huawei H19-135_V1.0問題集は専門家たちが数年間で過去のデータから分析して作成されて、試験にカバーする範囲は広くて、受験生の皆様のお金と時間を節約します。 それほかに品質はもっと高くてCiscoのCompTIA 220-1101認定試験「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」の受験生が最良の選択であり、成功の最高の保障でございます。

Updated: May 28, 2022