全てのIT専門人員はCiscoの350-401テストトレーニングの認定試験をよく知っていて、その難しい試験に受かることを望んでいます。Ciscoの350-401テストトレーニングの認定試験の認可を取ったら、あなたは望むキャリアを得ることができるようになります。NewValidDumpsのCiscoの350-401テストトレーニング試験トレーニング資料を利用したら、望むことを取得できます。 暇な時間だけでCiscoの350-401テストトレーニング試験に合格したいのですか。我々の提供するPDF版のCiscoの350-401テストトレーニング試験の資料はあなたにいつでもどこでも読めさせます。 NewValidDumps は世界的によく知られているサイトです。

350-401テストトレーニング問題集を利用して試験に合格できます。

そうすると、350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)テストトレーニング問題集の品質を知らないままに問題集を購入してから後悔になることを避けることができます。 NewValidDumpsにたくさんのIT専門人士がいって、弊社の問題集に社会のITエリートが認定されて、弊社の問題集は試験の大幅カーバして、合格率が１００％にまで達します。弊社のみたいなウエブサイトが多くても、彼たちは君の学習についてガイドやオンラインサービスを提供するかもしれないが、弊社はそちらにより勝ちます。

しかも、楽に試験に合格することができます。IT領域でより大きな進歩を望むなら、350-401テストトレーニング認定試験を受験する必要があります。IT試験に順調に合格することを望むなら、NewValidDumpsの350-401テストトレーニング問題集を使用する必要があります。

Cisco 350-401テストトレーニング - 近年、IT領域で競争がますます激しくなります。

競争力が激しい社会において、IT仕事をする人は皆、我々NewValidDumpsの350-401テストトレーニングを通して自らの幸せを筑く建筑士になれます。我が社のCiscoの350-401テストトレーニング習題を勉強して、最も良い結果を得ることができます。我々の350-401テストトレーニング習題さえ利用すれば試験の成功まで近くなると考えられます。

NewValidDumpsのCiscoの350-401テストトレーニング試験トレーニング資料は豊富な知識と経験を持っているIT専門家に研究された成果で、正確度がとても高いです。NewValidDumpsに会ったら、最高のトレーニング資料を見つけました。

350-401 PDF DEMO:

QUESTION NO: 1
Which description of an SD-Access wireless network infrastructure deployment is true?
A. The wireless client is part of the fabric overlay.
B. The access point is part of the fabric underlay.
C. The WLC is part of the fabric underlay.
D. The access point is part the fabric overlay.
Answer: B

QUESTION NO: 2
Which statement about a fabric access point is true?
A. It is in local mode an must connected directly to the fabric edge switch.
B. It is in FlexConnect mode and must be connected directly to the fabric edge switch.
C. It is in FlexConnect mode and must be connected directly to the fabric border node.
D. It is in local mode an must be connected directly to the fabric border node.
Answer: A
Explanation:
Fabric mode APs continue to support the same wireless media services that traditional APs support; apply AVC, quality of service (QoS), and other wireless policies; and establish the CAPWAP control plane to the fabric WLC. Fabric APs join as local-mode APs and must be directly connected to the fabric edge node switch to enable fabric registration events, including RLOC assignment via the fabric
WLC. The fabric edge nodes use CDP to recognize APs as special wired hosts, applying special port configurations and assigning the APs to a unique overlay network within a common EID space across a fabric. The assignment allows management simplification by using a single subnet to cover the AP infrastructure at a fabric site.
Reference: https://www.cisco.com/c/en/us/td/docs/solutions/CVD/Campus/sda-sdg-2019oct.html

QUESTION NO: 3
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").

QUESTION NO: 4
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 5
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

弊社NewValidDumpsのSAP C_SAC_2402問題集は必ずあなたの成功へ道の秘訣です。 NewValidDumpsのSAP C-TADM-23問題集の合格率が100%に達することも数え切れない受験生に証明された事実です。 SAP C-DBADM-2404 - 別の人の言い回しより自分の体験感じは大切なことです。 Lpi 050-100認定試験に合格することは難しいようですね。 他の人に先立ってCisco　Salesforce Salesforce-AI-Associate認定資格を得るために、今から勉強しましょう。

Updated: May 28, 2022