NewValidDumpsのCiscoの350-401テスト資料試験トレーニング資料は豊富な経験を持っているIT専門家が研究したものです。君がCiscoの350-401テスト資料問題集を購入したら、私たちは一年間で無料更新サービスを提供することができます。もしCiscoの350-401テスト資料問題集は問題があれば、或いは試験に不合格になる場合は、全額返金することを保証いたします。 そうしたら、半分の労力で二倍の効果を得ることができます。Ciscoの350-401テスト資料試験に受かるために一所懸命頑張って勉強していれば、あなたは間違っているのです。 弊社のNewValidDumpsはIT認定試験のソフトの一番信頼たるバンドになるという目標を達成するために、弊社はあなたに最新版のCiscoの350-401テスト資料試験問題集を提供いたします。

CCNP Enterprise 350-401 我々の商品にあなたを助けさせましょう。

CCNP Enterprise 350-401テスト資料 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) あなたはいつでもサブスクリプションの期間を延長することができますから、より多くの時間を取って充分に試験を準備できます。 弊社の350-401 勉強時間問題集は大勢の専門家たちの努力で開発される成果です。初心者といい、数年IT仕事を従事した人といい、我々NewValidDumpsのCisco　350-401 勉強時間問題集は最良の選択であると考えられます。

NewValidDumpsはとても良い選択で、350-401テスト資料の試験を最も短い時間に縮められますから、あなたの費用とエネルギーを節約することができます。それに、あなたに美しい未来を作ることに助けを差し上げられます。Ciscoの350-401テスト資料認定試験に受かるのはあなたの技能を検証することだけでなく、あなたの専門知識を証明できて、上司は無駄にあなたを雇うことはしないことの証明書です。

Cisco 350-401テスト資料 - だから、私たちは信頼されるに値します。

350-401テスト資料認定試験に合格することは難しいようですね。試験を申し込みたいあなたは、いまどうやって試験に準備すべきなのかで悩んでいますか。そうだったら、下記のものを読んでください。いま350-401テスト資料試験に合格するショートカットを教えてあげますから。あなたを試験に一発合格させる素晴らしい350-401テスト資料試験に関連する参考書が登場しますよ。それはNewValidDumpsの350-401テスト資料問題集です。気楽に試験に合格したければ、はやく試しに来てください。

もしあなたはまだ合格のためにCisco 350-401テスト資料に大量の貴重な時間とエネルギーをかかって一生懸命準備し、Cisco 350-401テスト資料「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験に合格するの近道が分からなくって、今はNewValidDumpsが有効なCisco 350-401テスト資料認定試験の合格の方法を提供して、君は半分の労力で倍の成果を取るの与えています。

350-401 PDF DEMO:

QUESTION NO: 1
Which statement about a fabric access point is true?
A. It is in local mode an must connected directly to the fabric edge switch.
B. It is in FlexConnect mode and must be connected directly to the fabric edge switch.
C. It is in FlexConnect mode and must be connected directly to the fabric border node.
D. It is in local mode an must be connected directly to the fabric border node.
Answer: A
Explanation:
Fabric mode APs continue to support the same wireless media services that traditional APs support; apply AVC, quality of service (QoS), and other wireless policies; and establish the CAPWAP control plane to the fabric WLC. Fabric APs join as local-mode APs and must be directly connected to the fabric edge node switch to enable fabric registration events, including RLOC assignment via the fabric
WLC. The fabric edge nodes use CDP to recognize APs as special wired hosts, applying special port configurations and assigning the APs to a unique overlay network within a common EID space across a fabric. The assignment allows management simplification by using a single subnet to cover the AP infrastructure at a fabric site.
Reference: https://www.cisco.com/c/en/us/td/docs/solutions/CVD/Campus/sda-sdg-2019oct.html

QUESTION NO: 2
Which description of an SD-Access wireless network infrastructure deployment is true?
A. The wireless client is part of the fabric overlay.
B. The access point is part of the fabric underlay.
C. The WLC is part of the fabric underlay.
D. The access point is part the fabric overlay.
Answer: B

QUESTION NO: 3
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").

QUESTION NO: 4
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 5
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

NetSuite SuiteFoundation - ここには、私たちは君の需要に応じます。 BCS CISMP-V9 - 君の初めての合格を目標にします。 うちのCiscoのCompTIA SY0-601-KR試験トレーニング資料を購入する前に、NewValidDumpsのサイトで、一部分のフリーな試験問題と解答をダンロードでき、試用してみます。 Amazon CLF-C01-KR - IT業界ではさらに強くなるために強い専門知識が必要です。 SAP C-TS462-2022-KR - 時間とお金の集まりより正しい方法がもっと大切です。

Updated: May 28, 2022