どの版でもCiscoの350-401日本語認定試験の復習資料は効果的なのを保証します。あなたはどのような方式で試験を準備するのが好きですか。PDF、オンライン問題集または模擬試験ソフトですか。 我々は心からあなたが首尾よく試験に合格することを願っています。あなたに便利なオンラインサービスを提供して、Cisco 350-401日本語認定試験問題についての全ての質問を解決して差し上げます。 全日でのオンライン係員、Ciscoの350-401日本語認定試験資料のデモ、豊富なバーション、Ciscoの350-401日本語認定試験資料を購入した後の無料更新、試験に失敗した後の全額の返金…これら全部は我々NewValidDumpsが信頼される理由です。

CCNP Enterprise 350-401 さて、はやく試験を申し込みましょう。

Cisco　350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)日本語認定試験問題集を購買してから、一年間の無料更新を楽しみにしています。 あなたは試験の最新バージョンを提供することを要求することもできます。最新の350-401 模擬対策問題試験問題を知りたい場合、試験に合格したとしてもNewValidDumpsは無料で問題集を更新してあげます。

そうしたら、Cisco　350-401日本語認定試験はそんなに簡単なことだと知られます。Cisco　350-401日本語認定試験を難しく感じる人に「やってもいないのに、できないと言わないこと」を言いたいです。我々NewValidDumpsへのCisco　350-401日本語認定試験問題集は専業化のチームが長時間で過去のデータから分析研究された成果で、あなたを試験に迅速的に合格できるのを助けます。

Cisco 350-401日本語認定 - 試験に失敗したら、全額で返金する承諾があります。

NewValidDumpsは最高な品質で最速なスピードでCiscoの350-401日本語認定認定試験の資料を更新するサイトでございます。もしかすると君はほかのサイトもCiscoの350-401日本語認定認証試験に関する資料があるのを見つけた、比較したらNewValidDumpsが提供したのがいちばん全面的で品質が最高なことがわかりました。

暇な時間だけでCiscoの350-401日本語認定試験に合格したいのですか。我々の提供するPDF版のCiscoの350-401日本語認定試験の資料はあなたにいつでもどこでも読めさせます。

350-401 PDF DEMO:

QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

NewValidDumpsは100%でCiscoのHuawei H12-311_V3.0「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認定試験に合格するのを保証いたします。 我々NewValidDumpsはCiscoのHuawei H19-135_V1.0試験問題集をリリースする以降、多くのお客様の好評を博したのは弊社にとって、大変な名誉なことです。 The Open Group OGEA-103 - NewValidDumpsのことに興味があったらネットで提供した部分資料をダウンロードしてください。 たとえば、ベストセラーのCisco　ISACA CISA-KR問題集は過去のデータを分析して作成ます。 Oracle 1z0-071 - 弊社の無料なサンプルを遠慮なくダウンロードしてください。

Updated: May 28, 2022