我々のCiscoの350-401日本語版受験参考書ソフトを利用してお客様の高通過率及び我々の技術の高いチームで、我々は自信を持って我々NewValidDumpsは専門的なのだと言えます。アフターサービスは会社を評価する重要な基準です。これをよくできるために、我々は全日24時間のサービスを提供します。 人に引けをとりたくないあなたはCisco　350-401日本語版受験参考書資格認定を取得したいですか。ここで、彼らは350-401日本語版受験参考書試験にうまく合格できる秘訣は我々社の提供する質高いCisco　350-401日本語版受験参考書問題集を利用したことだと教えます。 我々もオンライン版とソフト版を提供します。

CCNP Enterprise 350-401 あなたは成功な人生がほしいですか。

350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)日本語版受験参考書認定試験に合格することは難しいようですね。 NewValidDumpsは試験に失敗すれば全額返金を保証します。このような保証があれば、NewValidDumpsの350-401 キャリアパス問題集を購入しようか購入するまいかと躊躇する必要は全くないです。

一回だけでCiscoの350-401日本語版受験参考書試験に合格したい？NewValidDumpsは君の欲求を満たすために存在するのです。NewValidDumpsは君にとってベストな選択になります。ここには、私たちは君の需要に応じます。

Cisco 350-401日本語版受験参考書 - 我々の誠意を信じてください。

NewValidDumpsはきっとご存じしています。それは現在、市場上でCisco の350-401日本語版受験参考書認定試験に合格する率が一番高いからです。あなたはうちのCiscoの350-401日本語版受験参考書問題集を購入する前に、一部分のフリーな試験問題と解答をダンロードして、試用してみることができます。ご利用によってで、うちのCiscoの350-401日本語版受験参考書問題集は正確性が高いです。Ciscoの350-401日本語版受験参考書問題集を購入したら、私たちは一年間で無料更新サービスを提供することができます。

自分のIT業界での発展を希望したら、Ciscoの350-401日本語版受験参考書試験に合格する必要があります。Ciscoの350-401日本語版受験参考書試験はいくつ難しくても文句を言わないで、我々NewValidDumpsの提供する資料を通して、あなたはCiscoの350-401日本語版受験参考書試験に合格することができます。

350-401 PDF DEMO:

QUESTION NO: 1
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 2
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 4
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 5
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D

NewValidDumpsを選ぶなら、君がCiscoのPegasystems PEGACPDS24V1認定試験に合格するということできっと喜んでいます。 あなたは自分の望ましいCisco EC-COUNCIL 312-82問題集を選らんで、学びから更なる成長を求められます。 我々は力の限りにあなたにCiscoのISC CC試験に合格します。 短時間でISACA CISA試験に一発合格したいなら、我々社のCiscoのISACA CISA資料を参考しましょう。 我々NewValidDumpsの提供するCiscoのGoogle Professional-Cloud-Network-Engineer試験のソフトを利用した多くのお客様はこのような感じがあります。

Updated: May 28, 2022