NewValidDumpsの試験トレーニング資料はCiscoの350-401日本語版受験参考書認定試験の１００パーセントの合格率を保証します。近年、IT領域で競争がますます激しくなります。IT認証は同業種の欠くことができないものになりました。 」という声がよく聞こえています。NewValidDumpsは問題集を利用したことがある多くの人々からいろいろな好評を得ました。 NewValidDumpsで、あなたの試験のためのテクニックと勉強資料を見つけることができます。

CCNP Enterprise 350-401 まだなにを待っていますか。

CCNP Enterprise 350-401日本語版受験参考書 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) そうだったら、下記のものを読んでください。 NewValidDumpsの Ciscoの350-401 受験方法試験トレーニング資料は高度に認証されたIT領域の専門家の経験と創造を含めているものです。その権威性は言うまでもありません。

ここには、私たちは君の需要に応じます。NewValidDumpsのCiscoの350-401日本語版受験参考書問題集を購入したら、私たちは君のために、一年間無料で更新サービスを提供することができます。もし不合格になったら、私たちは全額返金することを保証します。

Cisco 350-401日本語版受験参考書 - 我々の誠意を信じてください。

暇な時間だけでCiscoの350-401日本語版受験参考書試験に合格したいのですか。我々の提供するPDF版のCiscoの350-401日本語版受験参考書試験の資料はあなたにいつでもどこでも読めさせます。我々もオンライン版とソフト版を提供します。すべては豊富な内容があって各自のメリットを持っています。あなたは各バーションのCiscoの350-401日本語版受験参考書試験の資料をダウンロードしてみることができ、あなたに一番ふさわしいバーションを見つけることができます。

自分のIT業界での発展を希望したら、Ciscoの350-401日本語版受験参考書試験に合格する必要があります。Ciscoの350-401日本語版受験参考書試験はいくつ難しくても文句を言わないで、我々NewValidDumpsの提供する資料を通して、あなたはCiscoの350-401日本語版受験参考書試験に合格することができます。

350-401 PDF DEMO:

QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 3
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

どこからCitrix 1Y0-341試験の優秀な資料を探すできるか？では、我々社NewValidDumpsのCitrix 1Y0-341問題集を選んでみてくださいませんか。 SailPoint IdentityNow-Engineer - 世の中に去年の自分より今年の自分が優れていないのは立派な恥です。 弊社のVMware 2V0-13.24問題集の購入について、決済手段は決済手段はpaypalによるお支払いでございますが、クレジットカードはpaypalにつながることができますから、クレジットカードの方もお支払いのこともできますということでございます。 短時間でHRCI PHRi試験に一発合格したいなら、我々社のCiscoのHRCI PHRi資料を参考しましょう。 EMC D-PDD-DY-23 - お客様の満足は我々の進む力です。

Updated: May 28, 2022