NewValidDumps のCiscoの350-401問題数「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」練習問題集と解答は実践の検査に合格したソフトウェアで、最も受験生に合うトレーニングツールです。NewValidDumpsで、あなたは一番良い準備資料を見つけられます。その資料は練習問題と解答に含まれています。 あなたは試験の最新バージョンを提供することを要求することもできます。最新の350-401問題数試験問題を知りたい場合、試験に合格したとしてもNewValidDumpsは無料で問題集を更新してあげます。 それに一年間の無料更新サービスを提供しますから、NewValidDumpsのウェブサイトをご覧ください。

CCNP Enterprise 350-401 」と思わないでください。

CCNP Enterprise 350-401問題数 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) 試験に失敗したら、全額で返金する承諾があります。 NewValidDumpsの資料はきっとあなたが350-401 関連日本語版問題集試験の認証資格を取ることを助けられます。現在の仕事に満足していますか。

我々もオンライン版とソフト版を提供します。すべては豊富な内容があって各自のメリットを持っています。あなたは各バーションのCiscoの350-401問題数試験の資料をダウンロードしてみることができ、あなたに一番ふさわしいバーションを見つけることができます。

Cisco 350-401問題数 - IT認定試験に合格するのは難しいと思いますか。

我々NewValidDumpsはCiscoの350-401問題数試験問題集をリリースする以降、多くのお客様の好評を博したのは弊社にとって、大変な名誉なことです。また、我々はさらに認可を受けられるために、皆様の一切の要求を満足できて喜ぶ気持ちでずっと協力し、完備かつ精確の350-401問題数試験問題集を開発するのに準備します。

この350-401問題数問題集はあなたを楽に試験に合格させる素晴らしいツールですから、この成功できチャンスを見逃せば絶対後悔になりますから、尻込みしないで急いで行動しましょう。ただ一つの試験の準備をするだけで時間をたくさん無駄にすることをやめてください。

350-401 PDF DEMO:

QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 2
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 5
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").

たとえば、ベストセラーのCisco　Google Professional-Data-Engineer問題集は過去のデータを分析して作成ます。 Cisco 700-841 - NewValidDumpsが提供した問題と解答はIT領域のエリートたちが研究して、実践して開発されたものです。 Microsoft AI-102問題集のカーバー率が高いので、勉強した問題は試験に出ることが多いです。 君がCiscoのSalesforce Salesforce-AI-Associate問題集を購入したら、私たちは一年間で無料更新サービスを提供することができます。 EMC D-DP-FN-01 - NewValidDumpsにたくさんのIT専門人士がいって、弊社の問題集に社会のITエリートが認定されて、弊社の問題集は試験の大幅カーバして、合格率が１００％にまで達します。

Updated: May 28, 2022