自分の幸せは自分で作るものだと思われます。ただ、社会に入るIT卒業生たちは自分能力の不足で、642-997資格講座試験向けの仕事を探すのを悩んでいますか？それでは、弊社のCiscoの642-997資格講座練習問題を選んで実用能力を速く高め、自分を充実させます。その結果、自信になる自己は面接のときに、面接官のいろいろな質問を気軽に回答できて、順調に642-997資格講座向けの会社に入ります。 うちの学習教材の内容は正確性が高くて、Ciscoの642-997資格講座認定試験に合格する率は１００パッセントになっていました。NewValidDumpsのCiscoの642-997資格講座試験トレーニング資料を手に入れたら、あなたは認定試験に合格する鍵を手に入れるというのに等しいです。 NewValidDumpsのCisco　642-997資格講座問題集は専門家たちが数年間で過去のデータから分析して作成されて、試験にカバーする範囲は広くて、受験生の皆様のお金と時間を節約します。

CCNP Data Center 642-997 暇の時間を利用して勉強します。

CCNP Data Center 642-997資格講座 - Implementing Cisco Data Center Unified Fabric (DCUFI) 試験に失敗したら、弊社は全額で返金します。 多分、642-997 学習指導テスト質問の数が伝統的な問題の数倍である。Cisco　642-997 学習指導試験参考書は全ての知識を含めて、全面的です。

我々のソフトは多くの受験生にCiscoの642-997資格講座試験に合格させました。我々の通過率はいくつ高くても、我々はあなたが試験に失敗したら全額で返金するのを保証します。これはあなたに安心で弊社の商品を購入させるためです。

Cisco 642-997資格講座 - 我々のデモを無料でやってみよう。

きみはCiscoの642-997資格講座認定テストに合格するためにたくさんのルートを選択肢があります。NewValidDumpsは君のために良い訓練ツールを提供し、君のCisco認証試に高品質の参考資料を提供しいたします。あなたの全部な需要を満たすためにいつも頑張ります。

あなたに相応しい642-997資格講座問題集を購入できさせるには、Ciscoは問題集の見本を無料に提供し、あなたはダウンロードしてやることができます。あなた642-997資格講座問題集を購入してから、一年間の無料更新サービスをていきょうします。

642-997 PDF DEMO:

QUESTION NO: 1
Which two functions are enabled when you set up vPC+ at the FabricPath edge? (Choose two.)
A. the ability to attach Cisco Fabric Extenders in FEX active/active mode
B. the ability to stop all Layer 3 egress traffic
C. the ability to attach servers to edge switches with port-channel teaming
D. the ability to attach additional Classic Ethernet switches in vPC+ mode
Answer: A,C

QUESTION NO: 2
Refer to the exhibit.
What is the consequence of configuring peer-gateway on the two vPC peers N7K-1 and N7K-2?
A. Nothing, this is the standard vPC configuration to make the feature work.
B. The downstream device detects only one of the vPC peers as its gateway.
C. The downstream device can use DMAC of N7K-1 on the link to N7K-2, and N7K-2 forwards the packet.
D. This configuration enables the downstream device to use DHCP to obtain its default gateway.
Answer: C
Explanation:
Beginning with Cisco NX-OS 4.2(1), you can configure vPC peer devices to act as the gateway even for packets that are destined to the vPC peer device's MAC address. Use the peer-gateway command to configure this feature.
Some network-attached storage (NAS) devices or load-balancers may have features aimed to optimize the performances of particular applications. Essentially these features avoid performing a routing-table lookup when responding to a request that originated form a host not locally attached to the same subnet. Such devices may reply to traffic using the MAC address of the sender Cisco Nexus
7000 device rather than the common HSRP gateway.
Such behavior is non-complaint with some basic Ethernet RFC standards. Packets reaching a vPC device for the non-local router MAC address are sent across the peer-link and could be dropped by the built in vPC loop avoidance mechanism if the final destination is behind another vPC.
The vPC peer-gateway capability allows a vPC switch to act as the active gateway for packets that are addressed to the router MAC address of the vPC peer. This feature enables local forwarding of such packets without the need to cross the vPC peer-link. In this scenario, the feature optimizes use of the peer-link and avoids potential traffic loss.
Configuring the peer-gateway feature needs to be done on both primary and secondary vPC peers and is non-disruptive to the operations of the device or to the vPC traffic. The vPC peer-gateway feature can be configured globally under the vPC domain submode.
When enabling this feature it is also required to disable IP redirects on all interface VLANs mapped over a vPC VLAN to avoid generation of IP redirect messages for packets switched through the peer gateway router. When the feature is enabled in the vPC domain, the user is notified of such a requirement through an appropriate message.
Packets arriving at the peer-gateway vPC device will have their TTL decremented, so packets carrying
TTL = 1 may be dropped in transit due to TTL expire. This needs to be taken into account when the peer-gateway feature is enabled and particular network protocols sourcing packets with TTL = 1 operate on a vPC VLAN.
Reference: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/4_2/nx- os/interfaces/configuration/guide/if_nxos/if_vPC.html

QUESTION NO: 3
What is the Overlay Transport Virtualization site VLAN used for?
A. to allow the join interfaces at different sites to communicate
B. to detect devices at the site that are not capable of OTV
C. to allow multiple site AEDs to communicate with each other
D. to detect other OTV edge devices in the site
Answer: D

QUESTION NO: 4
Which SCSI terminology is used to describe source and destination nodes?
A. hosts and targets
B. initiators and targets
C. HBA and disks
D. initiators and disks
E. HBA and targets
Answer: B
Explanation:
In computer data storage, a SCSI initiator is the endpoint that initiates a SCSI session, that is, sends a
SCSI command. The initiator usually does not provide any Logical Unit
Numbers (LUNs).
On the other hand, a SCSI target is the endpoint that does not initiate sessions, but instead waits for initiators' commands and provides required input/output data transfers. The target usually provides to the initiators one or more LUNs, because otherwise no read or write command would be possible.
Reference: http://en.wikipedia.org/wiki/SCSI_initiator_and_target

QUESTION NO: 5
Which task must be done before a zone set takes effect?
A. Add a member to the zone.
B. Enter the exit config t command.
C. Enter the copy running-config startup-config command.
D. Enter the zoneset activate name <zone-name> vsan <vsan-#> command.
Answer: D

NewValidDumpsの専門家チームがCiscoのMicrosoft SC-200認証試験に対して最新の短期有効なトレーニングプログラムを研究しました。 IAPP AIGP - あなたに行き届いたサービスを提供できるのは我々の幸いです。 NewValidDumpsのCiscoのAmazon SAA-C03認証試験について最新な研究を完成いたしました。 IBM C1000-184 - あなたの努力を無駄にするのは我々NewValidDumpsのすべきことです。 インターネットで時勢に遅れないDAMA CDMP-RMD勉強資料を提供するというサイトがあるかもしれませんが、NewValidDumpsはあなたに高品質かつ最新のCiscoのDAMA CDMP-RMDトレーニング資料を提供するユニークなサイトです。

Updated: May 28, 2022