今の社会の中で、ネット上で訓練は普及して、弊社は試験問題集を提供する多くのネットの一つでございます。NewValidDumpsが提供したのオンライン商品がIT業界では品質の高い学習資料、受験生の必要が満足できるサイトでございます。 それはNewValidDumpsがすごく便利で、広い通用性があるからです。NewValidDumpsのITエリートたちは彼らの専門的な目で、最新的なCiscoの642-997試験感想試験トレーニング資料に注目していて、うちのCiscoの642-997試験感想問題集の高い正確性を保証するのです。 試験問題と解答に関する質問があるなら、当社は直後に解決方法を差し上げます。

CCNP Data Center 642-997 夢を持ったら実現するために頑張ってください。

CCNP Data Center 642-997試験感想 - Implementing Cisco Data Center Unified Fabric (DCUFI) そうであれば、あなたは夢がある人だと思います。 きっと望んでいるでしょう。では、常に自分自身をアップグレードする必要があります。

我々NewValidDumpsのITエリートと我々のCiscoの642-997試験感想試験のソフトに満足するお客様は我々に自信を持たせます。あなたのCiscoの642-997試験感想試験を準備する圧力を減少するのは我々の責任で、あなたにCiscoの642-997試験感想試験に合格させるのは我々の目標です。我々はほぼ100％の通過率であなたに安心させます。

Cisco 642-997試験感想 - もちろんありますよ。

我々社はCisco　642-997試験感想問題集をリリースされる以来、たくさんの好評を博しました。試験に合格したお客様は「642-997試験感想問題集のオンライン版を利用して、模擬試験を繰り返して受けました。無事試験に合格しました。NewValidDumpsから大変助かりました。」と感謝します。あなたの支持こそ我々は最も高品質のCisco　642-997試験感想問題集を開発して努力します。

もしCiscoの642-997試験感想問題集は問題があれば、或いは試験に不合格になる場合は、全額返金することを保証いたします。NewValidDumpsのCiscoの642-997試験感想試験トレーニング資料は豊富な経験を持っているIT専門家が研究したものです。

642-997 PDF DEMO:

QUESTION NO: 1
Which two functions are enabled when you set up vPC+ at the FabricPath edge? (Choose two.)
A. the ability to attach Cisco Fabric Extenders in FEX active/active mode
B. the ability to stop all Layer 3 egress traffic
C. the ability to attach servers to edge switches with port-channel teaming
D. the ability to attach additional Classic Ethernet switches in vPC+ mode
Answer: A,C

QUESTION NO: 2
Refer to the exhibit.
What is the consequence of configuring peer-gateway on the two vPC peers N7K-1 and N7K-2?
A. Nothing, this is the standard vPC configuration to make the feature work.
B. The downstream device detects only one of the vPC peers as its gateway.
C. The downstream device can use DMAC of N7K-1 on the link to N7K-2, and N7K-2 forwards the packet.
D. This configuration enables the downstream device to use DHCP to obtain its default gateway.
Answer: C
Explanation:
Beginning with Cisco NX-OS 4.2(1), you can configure vPC peer devices to act as the gateway even for packets that are destined to the vPC peer device's MAC address. Use the peer-gateway command to configure this feature.
Some network-attached storage (NAS) devices or load-balancers may have features aimed to optimize the performances of particular applications. Essentially these features avoid performing a routing-table lookup when responding to a request that originated form a host not locally attached to the same subnet. Such devices may reply to traffic using the MAC address of the sender Cisco Nexus
7000 device rather than the common HSRP gateway.
Such behavior is non-complaint with some basic Ethernet RFC standards. Packets reaching a vPC device for the non-local router MAC address are sent across the peer-link and could be dropped by the built in vPC loop avoidance mechanism if the final destination is behind another vPC.
The vPC peer-gateway capability allows a vPC switch to act as the active gateway for packets that are addressed to the router MAC address of the vPC peer. This feature enables local forwarding of such packets without the need to cross the vPC peer-link. In this scenario, the feature optimizes use of the peer-link and avoids potential traffic loss.
Configuring the peer-gateway feature needs to be done on both primary and secondary vPC peers and is non-disruptive to the operations of the device or to the vPC traffic. The vPC peer-gateway feature can be configured globally under the vPC domain submode.
When enabling this feature it is also required to disable IP redirects on all interface VLANs mapped over a vPC VLAN to avoid generation of IP redirect messages for packets switched through the peer gateway router. When the feature is enabled in the vPC domain, the user is notified of such a requirement through an appropriate message.
Packets arriving at the peer-gateway vPC device will have their TTL decremented, so packets carrying
TTL = 1 may be dropped in transit due to TTL expire. This needs to be taken into account when the peer-gateway feature is enabled and particular network protocols sourcing packets with TTL = 1 operate on a vPC VLAN.
Reference: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/4_2/nx- os/interfaces/configuration/guide/if_nxos/if_vPC.html

QUESTION NO: 3
What is the Overlay Transport Virtualization site VLAN used for?
A. to allow the join interfaces at different sites to communicate
B. to detect devices at the site that are not capable of OTV
C. to allow multiple site AEDs to communicate with each other
D. to detect other OTV edge devices in the site
Answer: D

QUESTION NO: 4
Which SCSI terminology is used to describe source and destination nodes?
A. hosts and targets
B. initiators and targets
C. HBA and disks
D. initiators and disks
E. HBA and targets
Answer: B
Explanation:
In computer data storage, a SCSI initiator is the endpoint that initiates a SCSI session, that is, sends a
SCSI command. The initiator usually does not provide any Logical Unit
Numbers (LUNs).
On the other hand, a SCSI target is the endpoint that does not initiate sessions, but instead waits for initiators' commands and provides required input/output data transfers. The target usually provides to the initiators one or more LUNs, because otherwise no read or write command would be possible.
Reference: http://en.wikipedia.org/wiki/SCSI_initiator_and_target

QUESTION NO: 5
Which task must be done before a zone set takes effect?
A. Add a member to the zone.
B. Enter the exit config t command.
C. Enter the copy running-config startup-config command.
D. Enter the zoneset activate name <zone-name> vsan <vsan-#> command.
Answer: D

常にCisco　Google Professional-Cloud-Architect-JPN試験に参加する予定があるお客様は「こちらの問題集には、全部で何問位、掲載されておりますか？」といった質問を提出しました。 弊社のNewValidDumpsはIT認定試験のソフトの一番信頼たるバンドになるという目標を達成するために、弊社はあなたに最新版のCiscoのFortinet NSE5_FMG-7.2-JPN試験問題集を提供いたします。 Microsoft MB-240試験に対して、いろいろな資料があります。 我々のCiscoのFortinet FCSS_NST_SE-7.4ソフトを利用してお客様の高通過率及び我々の技術の高いチームで、我々は自信を持って我々NewValidDumpsは専門的なのだと言えます。 でも、Cisco　Citrix 1Y0-204J復習教材を選ばれば、試験に合格することは簡単です。

Updated: May 28, 2022