ITを通して自分の実力を証明したいのですか。IT業界に従事したいなら、IT認定試験を受験して認証資格を取得することは必要になります。あなたが今しなければならないのは、広く認識された価値があるIT認定試験を受けることです。 NewValidDumpsで、あなたの試験のためのテクニックと勉強資料を見つけることができます。NewValidDumpsのCiscoの642-997模擬問題試験トレーニング資料は豊富な知識と経験を持っているIT専門家に研究された成果で、正確度がとても高いです。 それは NewValidDumpsの642-997模擬問題問題集には実際の試験に出題される可能性がある問題をすべて含んでいて、しかもあなたをよりよく問題を理解させるように詳しい解析を与えますから。

CCNP Data Center 642-997 不思議でしょう。

CCNP Data Center 642-997模擬問題 - Implementing Cisco Data Center Unified Fabric (DCUFI) 気楽に試験に合格したければ、はやく試しに来てください。 それは正確的な試験の内容を保証しますし、良いサービスで、安い価格で営業します。NewValidDumpsがあれば、Ciscoの642-997 資格復習テキスト試験に合格するのは心配しません。

ここには、私たちは君の需要に応じます。NewValidDumpsのCiscoの642-997模擬問題問題集を購入したら、私たちは君のために、一年間無料で更新サービスを提供することができます。もし不合格になったら、私たちは全額返金することを保証します。

Cisco 642-997模擬問題 - NewValidDumpsを選ぶなら、絶対に後悔させません。

NewValidDumpsのCiscoの642-997模擬問題試験トレーニング資料は試験問題と解答を含まれて、豊富な経験を持っているIT業種の専門家が長年の研究を通じて作成したものです。その権威性は言うまでもありません。うちのCiscoの642-997模擬問題試験トレーニング資料を購入する前に、NewValidDumpsのサイトで、一部分のフリーな試験問題と解答をダンロードでき、試用してみます。君がうちの学習教材を購入した後、私たちは一年間で無料更新サービスを提供することができます。

私たちは最も新しくて、最も正確性の高いCiscoの642-997模擬問題試験トレーニング資料を提供します。長年の努力を通じて、NewValidDumpsのCiscoの642-997模擬問題認定試験の合格率が１００パーセントになっていました。

642-997 PDF DEMO:

QUESTION NO: 1
Which SCSI terminology is used to describe source and destination nodes?
A. hosts and targets
B. initiators and targets
C. HBA and disks
D. initiators and disks
E. HBA and targets
Answer: B
Explanation:
In computer data storage, a SCSI initiator is the endpoint that initiates a SCSI session, that is, sends a
SCSI command. The initiator usually does not provide any Logical Unit
Numbers (LUNs).
On the other hand, a SCSI target is the endpoint that does not initiate sessions, but instead waits for initiators' commands and provides required input/output data transfers. The target usually provides to the initiators one or more LUNs, because otherwise no read or write command would be possible.
Reference: http://en.wikipedia.org/wiki/SCSI_initiator_and_target

QUESTION NO: 2
Which task must be done before a zone set takes effect?
A. Add a member to the zone.
B. Enter the exit config t command.
C. Enter the copy running-config startup-config command.
D. Enter the zoneset activate name <zone-name> vsan <vsan-#> command.
Answer: D

QUESTION NO: 3
Refer to the exhibit.
What is the consequence of configuring peer-gateway on the two vPC peers N7K-1 and N7K-2?
A. Nothing, this is the standard vPC configuration to make the feature work.
B. The downstream device detects only one of the vPC peers as its gateway.
C. The downstream device can use DMAC of N7K-1 on the link to N7K-2, and N7K-2 forwards the packet.
D. This configuration enables the downstream device to use DHCP to obtain its default gateway.
Answer: C
Explanation:
Beginning with Cisco NX-OS 4.2(1), you can configure vPC peer devices to act as the gateway even for packets that are destined to the vPC peer device's MAC address. Use the peer-gateway command to configure this feature.
Some network-attached storage (NAS) devices or load-balancers may have features aimed to optimize the performances of particular applications. Essentially these features avoid performing a routing-table lookup when responding to a request that originated form a host not locally attached to the same subnet. Such devices may reply to traffic using the MAC address of the sender Cisco Nexus
7000 device rather than the common HSRP gateway.
Such behavior is non-complaint with some basic Ethernet RFC standards. Packets reaching a vPC device for the non-local router MAC address are sent across the peer-link and could be dropped by the built in vPC loop avoidance mechanism if the final destination is behind another vPC.
The vPC peer-gateway capability allows a vPC switch to act as the active gateway for packets that are addressed to the router MAC address of the vPC peer. This feature enables local forwarding of such packets without the need to cross the vPC peer-link. In this scenario, the feature optimizes use of the peer-link and avoids potential traffic loss.
Configuring the peer-gateway feature needs to be done on both primary and secondary vPC peers and is non-disruptive to the operations of the device or to the vPC traffic. The vPC peer-gateway feature can be configured globally under the vPC domain submode.
When enabling this feature it is also required to disable IP redirects on all interface VLANs mapped over a vPC VLAN to avoid generation of IP redirect messages for packets switched through the peer gateway router. When the feature is enabled in the vPC domain, the user is notified of such a requirement through an appropriate message.
Packets arriving at the peer-gateway vPC device will have their TTL decremented, so packets carrying
TTL = 1 may be dropped in transit due to TTL expire. This needs to be taken into account when the peer-gateway feature is enabled and particular network protocols sourcing packets with TTL = 1 operate on a vPC VLAN.
Reference: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/4_2/nx- os/interfaces/configuration/guide/if_nxos/if_vPC.html

QUESTION NO: 4
DRAG DROP
Drag the description on the left to the most appropriate Nexus product on the right.
Answer:

QUESTION NO: 5
Which two functions are enabled when you set up vPC+ at the FabricPath edge? (Choose two.)
A. the ability to attach Cisco Fabric Extenders in FEX active/active mode
B. the ability to stop all Layer 3 egress traffic
C. the ability to attach servers to edge switches with port-channel teaming
D. the ability to attach additional Classic Ethernet switches in vPC+ mode
Answer: A,C

SAP C-S43-2023 - 我々の誠意を信じてください。 CiscoのISACA CISM-JPNソフトはあなたにITという職業での人材に鳴らせます。 自分のIT業界での発展を希望したら、CiscoのHuawei H13-311_V3.5試験に合格する必要があります。 我々NewValidDumpsがあなたに提供するCiscoのSAP C_S4CFI_2408ソフトはこれを保証します。 Cisco CCST-Networking-JPN - 世の中に去年の自分より今年の自分が優れていないのは立派な恥です。

Updated: May 28, 2022