自分のスキルを向上させ、よりよく他の人に自分の能力を証明したいですか。昇進する機会を得たいですか。そうすると、はやく642-997日本語版テキスト内容認定試験を申し込んで認証資格を取りましょう。 我々の誠意を信じてください。あなたが順調に試験に合格するように。 あなたはうちのCiscoの642-997日本語版テキスト内容問題集を購入する前に、一部分のフリーな試験問題と解答をダンロードして、試用してみることができます。

CCNP Data Center 642-997 早くNewValidDumpsの問題集を君の手に入れましょう。

有効的なCisco　642-997 - Implementing Cisco Data Center Unified Fabric (DCUFI)日本語版テキスト内容認定資格試験問題集を見つけられるのは資格試験にとって重要なのです。 君が後悔しないようにもっと少ないお金を使って大きな良い成果を取得するためにNewValidDumpsを選択してください。NewValidDumpsはまた一年間に無料なサービスを更新いたします。

今まで、たくさんのお客様はCisco　642-997日本語版テキスト内容試験参考資料に満足しています。そのほかに、弊社は引き続くみんなに合理的な価格で高品質な642-997日本語版テキスト内容参考資料を提供します。もちろん、いいサービスを提供し、642-997日本語版テキスト内容参考資料について、何か質問がありましたら、遠慮なく弊社と連絡します。

Cisco 642-997日本語版テキスト内容 - NewValidDumpsはこの問題を着々解決できますよ。

NewValidDumpsの642-997日本語版テキスト内容問題集は多くの受験生に検証されたものですから、高い成功率を保証できます。もしこの問題集を利用してからやはり試験に不合格になってしまえば、NewValidDumpsは全額で返金することができます。あるいは、無料で試験642-997日本語版テキスト内容問題集を更新してあげるのを選択することもできます。こんな保障がありますから、心配する必要は全然ないですよ。

NewValidDumpsは一番よい、一番実用的な、一番完全な試験トレーニング資料を提供していますから、受験生たちが試験を準備することに意重要な助けになります。適切なトレーニングを選ぶのは成功の保証になれますが、何を選ぶのは非常に重要なことです。

642-997 PDF DEMO:

QUESTION NO: 1
Which task must be done before a zone set takes effect?
A. Add a member to the zone.
B. Enter the exit config t command.
C. Enter the copy running-config startup-config command.
D. Enter the zoneset activate name <zone-name> vsan <vsan-#> command.
Answer: D

QUESTION NO: 2
Which SCSI terminology is used to describe source and destination nodes?
A. hosts and targets
B. initiators and targets
C. HBA and disks
D. initiators and disks
E. HBA and targets
Answer: B
Explanation:
In computer data storage, a SCSI initiator is the endpoint that initiates a SCSI session, that is, sends a
SCSI command. The initiator usually does not provide any Logical Unit
Numbers (LUNs).
On the other hand, a SCSI target is the endpoint that does not initiate sessions, but instead waits for initiators' commands and provides required input/output data transfers. The target usually provides to the initiators one or more LUNs, because otherwise no read or write command would be possible.
Reference: http://en.wikipedia.org/wiki/SCSI_initiator_and_target

QUESTION NO: 3
DRAG DROP
Drag the description on the left to the most appropriate Nexus product on the right.
Answer:

QUESTION NO: 4
Refer to the exhibit.
What is the consequence of configuring peer-gateway on the two vPC peers N7K-1 and N7K-2?
A. Nothing, this is the standard vPC configuration to make the feature work.
B. The downstream device detects only one of the vPC peers as its gateway.
C. The downstream device can use DMAC of N7K-1 on the link to N7K-2, and N7K-2 forwards the packet.
D. This configuration enables the downstream device to use DHCP to obtain its default gateway.
Answer: C
Explanation:
Beginning with Cisco NX-OS 4.2(1), you can configure vPC peer devices to act as the gateway even for packets that are destined to the vPC peer device's MAC address. Use the peer-gateway command to configure this feature.
Some network-attached storage (NAS) devices or load-balancers may have features aimed to optimize the performances of particular applications. Essentially these features avoid performing a routing-table lookup when responding to a request that originated form a host not locally attached to the same subnet. Such devices may reply to traffic using the MAC address of the sender Cisco Nexus
7000 device rather than the common HSRP gateway.
Such behavior is non-complaint with some basic Ethernet RFC standards. Packets reaching a vPC device for the non-local router MAC address are sent across the peer-link and could be dropped by the built in vPC loop avoidance mechanism if the final destination is behind another vPC.
The vPC peer-gateway capability allows a vPC switch to act as the active gateway for packets that are addressed to the router MAC address of the vPC peer. This feature enables local forwarding of such packets without the need to cross the vPC peer-link. In this scenario, the feature optimizes use of the peer-link and avoids potential traffic loss.
Configuring the peer-gateway feature needs to be done on both primary and secondary vPC peers and is non-disruptive to the operations of the device or to the vPC traffic. The vPC peer-gateway feature can be configured globally under the vPC domain submode.
When enabling this feature it is also required to disable IP redirects on all interface VLANs mapped over a vPC VLAN to avoid generation of IP redirect messages for packets switched through the peer gateway router. When the feature is enabled in the vPC domain, the user is notified of such a requirement through an appropriate message.
Packets arriving at the peer-gateway vPC device will have their TTL decremented, so packets carrying
TTL = 1 may be dropped in transit due to TTL expire. This needs to be taken into account when the peer-gateway feature is enabled and particular network protocols sourcing packets with TTL = 1 operate on a vPC VLAN.
Reference: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/4_2/nx- os/interfaces/configuration/guide/if_nxos/if_vPC.html

QUESTION NO: 5
If vPC peer keepalives are used between vPC peers, which VRF is used by default?
A. management
B. default
C. The user must dedicate a VRF for keepalives.
D. system
Answer: A

NewValidDumpsのITエリートたちは彼らの専門的な目で、最新的なCiscoのSalesforce MuleSoft-Integration-Associate試験トレーニング資料に注目していて、うちのCiscoのSalesforce MuleSoft-Integration-Associate問題集の高い正確性を保証するのです。 全てのCiscoのSalesforce Marketing-Cloud-Developer「Implementing Cisco Data Center Unified Fabric (DCUFI)」試験は非常に大切ですが、この情報技術が急速に発展している時代に、NewValidDumpsはただその中の一つだけです。 CiscoのCisco 350-401認定試験に合格することはきっと君の職業生涯の輝い将来に大変役に立ちます。 NewValidDumps CiscoのMicrosoft MB-310試験問題集はあなたが自分の目標を達成することを助けられます。 我々NewValidDumpsは一番効果的な方法を探してあなたにCiscoのJuniper JN0-280試験に合格させます。

Updated: May 28, 2022