私たちの642-997出題範囲試験参考書は、あなたが642-997出題範囲試験に合格する前に最高のサービスを提供することを保証します。これは確かに大きなチャンスです。絶対見逃さないです。 NewValidDumpsのCiscoの642-997出題範囲問題集を購入するなら、君がCiscoの642-997出題範囲認定試験に合格する率は１００パーセントです。あなたはNewValidDumpsの学習教材を購入した後、私たちは一年間で無料更新サービスを提供することができます。 弊社のNewValidDumps商品を安心に選択してNewValidDumps試験に100%合格しましょう。

CCNP Data Center 642-997 できるだけ100％の通過率を保証使用にしています。

CCNP Data Center 642-997出題範囲 - Implementing Cisco Data Center Unified Fabric (DCUFI) しかし必ずしも大量の時間とエネルギーで復習しなくて、弊社が丹精にできあがった問題集を使って、試験なんて問題ではありません。 ただ、社会に入るIT卒業生たちは自分能力の不足で、642-997 受験料試験向けの仕事を探すのを悩んでいますか？それでは、弊社のCiscoの642-997 受験料練習問題を選んで実用能力を速く高め、自分を充実させます。その結果、自信になる自己は面接のときに、面接官のいろいろな質問を気軽に回答できて、順調に642-997 受験料向けの会社に入ります。

Ciscoの642-997出題範囲認定試験は競争が激しい今のIT業界中でいよいよ人気があって、受験者が増え一方で難度が低くなくて結局専門知識と情報技術能力の要求が高い試験なので、普通の人がCisco認証試験に合格するのが必要な時間とエネルギーをかからなければなりません。

Cisco 642-997出題範囲 - これは前例のない真実かつ正確なものです。

きみはCiscoの642-997出題範囲認定テストに合格するためにたくさんのルートを選択肢があります。NewValidDumpsは君のために良い訓練ツールを提供し、君のCisco認証試に高品質の参考資料を提供しいたします。あなたの全部な需要を満たすためにいつも頑張ります。

」このように質問した人がいます。私は答えてあげますよ。

642-997 PDF DEMO:

QUESTION NO: 1
Which task must be done before a zone set takes effect?
A. Add a member to the zone.
B. Enter the exit config t command.
C. Enter the copy running-config startup-config command.
D. Enter the zoneset activate name <zone-name> vsan <vsan-#> command.
Answer: D

QUESTION NO: 2
Which SCSI terminology is used to describe source and destination nodes?
A. hosts and targets
B. initiators and targets
C. HBA and disks
D. initiators and disks
E. HBA and targets
Answer: B
Explanation:
In computer data storage, a SCSI initiator is the endpoint that initiates a SCSI session, that is, sends a
SCSI command. The initiator usually does not provide any Logical Unit
Numbers (LUNs).
On the other hand, a SCSI target is the endpoint that does not initiate sessions, but instead waits for initiators' commands and provides required input/output data transfers. The target usually provides to the initiators one or more LUNs, because otherwise no read or write command would be possible.
Reference: http://en.wikipedia.org/wiki/SCSI_initiator_and_target

QUESTION NO: 3
DRAG DROP
Drag the description on the left to the most appropriate Nexus product on the right.
Answer:

QUESTION NO: 4
Refer to the exhibit.
What is the consequence of configuring peer-gateway on the two vPC peers N7K-1 and N7K-2?
A. Nothing, this is the standard vPC configuration to make the feature work.
B. The downstream device detects only one of the vPC peers as its gateway.
C. The downstream device can use DMAC of N7K-1 on the link to N7K-2, and N7K-2 forwards the packet.
D. This configuration enables the downstream device to use DHCP to obtain its default gateway.
Answer: C
Explanation:
Beginning with Cisco NX-OS 4.2(1), you can configure vPC peer devices to act as the gateway even for packets that are destined to the vPC peer device's MAC address. Use the peer-gateway command to configure this feature.
Some network-attached storage (NAS) devices or load-balancers may have features aimed to optimize the performances of particular applications. Essentially these features avoid performing a routing-table lookup when responding to a request that originated form a host not locally attached to the same subnet. Such devices may reply to traffic using the MAC address of the sender Cisco Nexus
7000 device rather than the common HSRP gateway.
Such behavior is non-complaint with some basic Ethernet RFC standards. Packets reaching a vPC device for the non-local router MAC address are sent across the peer-link and could be dropped by the built in vPC loop avoidance mechanism if the final destination is behind another vPC.
The vPC peer-gateway capability allows a vPC switch to act as the active gateway for packets that are addressed to the router MAC address of the vPC peer. This feature enables local forwarding of such packets without the need to cross the vPC peer-link. In this scenario, the feature optimizes use of the peer-link and avoids potential traffic loss.
Configuring the peer-gateway feature needs to be done on both primary and secondary vPC peers and is non-disruptive to the operations of the device or to the vPC traffic. The vPC peer-gateway feature can be configured globally under the vPC domain submode.
When enabling this feature it is also required to disable IP redirects on all interface VLANs mapped over a vPC VLAN to avoid generation of IP redirect messages for packets switched through the peer gateway router. When the feature is enabled in the vPC domain, the user is notified of such a requirement through an appropriate message.
Packets arriving at the peer-gateway vPC device will have their TTL decremented, so packets carrying
TTL = 1 may be dropped in transit due to TTL expire. This needs to be taken into account when the peer-gateway feature is enabled and particular network protocols sourcing packets with TTL = 1 operate on a vPC VLAN.
Reference: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/4_2/nx- os/interfaces/configuration/guide/if_nxos/if_vPC.html

QUESTION NO: 5
If vPC peer keepalives are used between vPC peers, which VRF is used by default?
A. management
B. default
C. The user must dedicate a VRF for keepalives.
D. system
Answer: A

NewValidDumpsの専門家チームがCiscoのCompTIA FC0-U61J認証試験に対して最新の短期有効なトレーニングプログラムを研究しました。 NewValidDumpsのCiscoのMicrosoft AZ-400J試験トレーニング資料を持っていますから、どんなに難しい試験でも成功することができます。 Salesforce Salesforce-MuleSoft-Developer-II - きっと君に失望させないと信じています。 CiscoのHP HPE6-A78認定試験に合格したいのなら、NewValidDumpsのCiscoのHP HPE6-A78試験トレーニング資料を利用してください。 Blue Prism AD01-JPN - 我々は受験生の皆様により高いスピードを持っているかつ効率的なサービスを提供することにずっと力を尽くしていますから、あなたが貴重な時間を節約することに助けを差し上げます。

Updated: May 28, 2022