NewValidDumpsのIT専門家たちは受験生の皆さんのニーズを満たすように彼らの豊富な知識と経験を活かして試験トレーニング資料の品質をずっと高めています。受験生の皆さんが一回でCiscoの350-401絶対合格試験に合格することを保証します。NewValidDumpsの製品を購入したら、あなたはいつでも最新かつ最正確な試験情報を得ることができます。 Ciscoの350-401絶対合格試験はいくつ難しくても文句を言わないで、我々NewValidDumpsの提供する資料を通して、あなたはCiscoの350-401絶対合格試験に合格することができます。Ciscoの350-401絶対合格試験を準備しているあなたに試験に合格させるために、我々NewValidDumpsは模擬試験ソフトを更新し続けています。 あなたもIT認証資格を取りたいですか。

CCNP Enterprise 350-401 弊社の商品が好きなのは弊社のたのしいです。

NewValidDumpsは君のCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)絶対合格認定試験に合格するという夢を叶えるための存在です。 NewValidDumps を選択して１００％の合格率を確保することができて、もし試験に失敗したら、NewValidDumpsが全額で返金いたします。

あなたが安心で試験のために準備すればいいです。たぶん、あなたは苦しく準備してCiscoの350-401絶対合格試験に合格できないのを心配しています。おそらくあなたはお金がかかって買ったソフトが役に立たないのを心配しています。

Cisco 350-401絶対合格 - NewValidDumpsを選んだら、成功への扉を開きます。

数年以来の整理と分析によって開発された350-401絶対合格問題集は権威的で全面的です。350-401絶対合格問題集を利用して試験に合格できます。この問題集の合格率は高いので、多くのお客様から350-401絶対合格問題集への好評をもらいました。350-401絶対合格問題集のカーバー率が高いので、勉強した問題は試験に出ることが多いです。だから、弊社の提供する350-401絶対合格問題集を暗記すれば、きっと試験に合格できます。

したがって、NewValidDumpsの350-401絶対合格問題集も絶えずに更新されています。それに、NewValidDumpsの教材を購入すれば、NewValidDumpsは一年間の無料アップデート・サービスを提供してあげます。

350-401 PDF DEMO:

QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

そのため、SAP C-C4H47I-34試験参考書に対して、お客様の新たな要求に迅速に対応できます。 あるいは、無料で試験ECCouncil 312-85問題集を更新してあげるのを選択することもできます。 HP HPE0-V25J - NewValidDumpsはもっぱら認定試験に参加するIT業界の専門の人士になりたい方のために模擬試験の練習問題と解答を提供した評判の高いサイトでございます。 SAP C_SAC_2402 - なぜ受験生のほとんどはNewValidDumpsを選んだのですか。 CompTIA 220-1102J - でも、この試験はそれほど簡単ではありません。

Updated: May 28, 2022