その中で、350-401的中関連問題認定試験は最も重要な一つです。では、この試験に合格するためにどのように試験の準備をしているのですか。がむしゃらに試験に関連する知識を勉強しているのですか。 NewValidDumpsはCiscoの350-401的中関連問題認定試験に向けてもっともよい問題集を研究しています。もしほかのホームページに弊社みたいな問題集を見れば、あとでみ続けて、弊社の商品を盗作することとよくわかります。 早速買いに行きましょう。

CCNP Enterprise 350-401 NewValidDumpsを選択したら、成功をとりましょう。

自分の能力を証明するために、350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)的中関連問題試験に合格するのは不可欠なことです。 NewValidDumpsの勉強資料を手に入れたら、指示に従えば 350-401 資料的中率認定試験に受かることはたやすくなります。受験生の皆様にもっと多くの助けを差し上げるために、NewValidDumps のCiscoの350-401 資料的中率トレーニング資料はインターネットであなたの緊張を解消することができます。

我々NewValidDumpsは一番行き届いたアフタサービスを提供します。Cisco　350-401的中関連問題試験問題集を購買してから、一年間の無料更新を楽しみにしています。あなたにCisco　350-401的中関連問題試験に関する最新かつ最完備の資料を勉強させ、試験に合格させることだと信じます。

Cisco 350-401的中関連問題 - これも現代社会が圧力に満ちている一つの反映です。

Cisco 350-401的中関連問題「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験に合格することが簡単ではなくて、Cisco 350-401的中関連問題証明書は君にとってはIT業界に入るの一つの手づるになるかもしれません。しかし必ずしも大量の時間とエネルギーで復習しなくて、弊社が丹精にできあがった問題集を使って、試験なんて問題ではありません。

NewValidDumpsの350-401的中関連問題問題集はあなたが楽に試験に合格する保障です。この問題集は大量な時間を節約させ、効率的に試験に準備させることができます。

350-401 PDF DEMO:

QUESTION NO: 1
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 2
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").

QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 4
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 5
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

Microsoft DP-420J - 今の社会の中で、ネット上で訓練は普及して、弊社は試験問題集を提供する多くのネットの一つでございます。 SAP E_S4CPE_2023 - それは問題ではないですよ。 NewValidDumpsは実際の環境で本格的なCiscoのEC-COUNCIL 312-39「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」の試験の準備過程を提供しています。 ですから、はやくNewValidDumpsのOracle 1z1-808-KR問題集を入手しましょう。 Salesforce Marketing-Cloud-Account-Engagement-Specialist - 我々は心からあなたが首尾よく試験に合格することを願っています。

Updated: May 28, 2022