Ciscoの認証資格は最近ますます人気になっていますね。国際的に認可された資格として、Ciscoの認定試験を受ける人も多くなっています。その中で、350-401日本語独学書籍認定試験は最も重要な一つです。 NewValidDumpsが提供した資料は最も全面的で、しかも更新の最も速いです。NewValidDumpsはその近道を提供し、君の多くの時間と労力も節約します。 なぜなら、それはCiscoの350-401日本語独学書籍認定試験に関する必要なものを含まれるからです。

CCNP Enterprise 350-401 それは正確性が高くて、カバー率も広いです。

CCNP Enterprise 350-401日本語独学書籍 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) NewValidDumpsは君に対して特別の訓練を提供しています。 我々はあなたに提供するのは最新で一番全面的なCiscoの350-401 必殺問題集問題集で、最も安全な購入保障で、最もタイムリーなCiscoの350-401 必殺問題集試験のソフトウェアの更新です。無料デモはあなたに安心で購入して、購入した後1年間の無料Ciscoの350-401 必殺問題集試験の更新はあなたに安心で試験を準備することができます、あなたは確実に購入を休ませることができます私たちのソフトウェアを試してみてください。

NewValidDumpsはたくさんの方がIT者になる夢を実現させるサイトでございます。NewValidDumpsはCiscoの350-401日本語独学書籍認証試験について最新の対応性教育テストツールを研究し続けて、Ciscoの350-401日本語独学書籍認定試験の問題集を開発いたしました。NewValidDumpsが提供したCiscoの350-401日本語独学書籍試験問題と解答が真実の試験の練習問題と解答は最高の相似性があり、一年の無料オンラインの更新のサービスがあり、100%のパス率を保証して、もし試験に合格しないと、弊社は全額で返金いたします。

Cisco 350-401日本語独学書籍 - NewValidDumpsを選択したら、成功をとりましょう。

社会と経済の発展につれて、多くの人はIT技術を勉強します。なぜならば、IT職員にとって、Ciscoの350-401日本語独学書籍資格証明書があるのは肝心な指標であると言えます。自分の能力を証明するために、350-401日本語独学書籍試験に合格するのは不可欠なことです。弊社の350-401日本語独学書籍真題を入手して、試験に合格する可能性が大きくなります。

350-401日本語独学書籍 勉強資料は公式Ciscoの350-401日本語独学書籍試験トレーニング授業 、Ciscoの350-401日本語独学書籍 自習ガイド、Ciscoの350-401日本語独学書籍 の試験と実践やCiscoの350-401日本語独学書籍オンラインテストなどに含まれています。NewValidDumps がデザインしたCiscoの350-401日本語独学書籍模擬トレーニングパッケージはあなたが楽に試験に合格することを助けます。

350-401 PDF DEMO:

QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

あなたにCisco　OMG OMG-OCUP2-ADV300試験に関する最新かつ最完備の資料を勉強させ、試験に合格させることだと信じます。 Cisco 200-301J - それに、あなたに美しい未来を作ることに助けを差し上げられます。 周りの多くの人は全部Cisco　Cisco 350-401資格認定試験にパースしまして、彼らはどのようにできましたか。 SAP C_C4H630_34 - 現在の時代で高効率は避けられない話題ですから、速いスピードと高効率が我々の目標です。 そうすれば、あなたは簡単にSalesforce Interaction-Studio-Accredited-Professional復習教材のデモを無料でダウンロードできます。

Updated: May 28, 2022