あなたはCiscoの350-401学習教材資格認定のために、他人より多くの時間をかかるんですか？NewValidDumpsの350-401学習教材問題集を紹介させてください。350-401学習教材は専門家たちが長年の経験で研究分析した勉強資料です。受験生のあなたを助けて時間とお金を節約したり、350-401学習教材試験に速く合格すると保証します。 それに、NewValidDumpsの教材を購入すれば、NewValidDumpsは一年間の無料アップデート・サービスを提供してあげます。問題が更新される限り、NewValidDumpsは直ちに最新版の350-401学習教材資料を送ってあげます。 これなので、IT技術職員としてのあなたはNewValidDumpsのCisco　350-401学習教材問題集デモを参考し、試験の準備に速く行動しましょう。

CCNP Enterprise 350-401 絶対見逃さないです。

Ciscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)学習教材認定試験に合格することはきっと君の職業生涯の輝い将来に大変役に立ちます。 もしあなたはNewValidDumpsの製品を購入したければ弊社が詳しい問題集を提供して、君にとって完全に準備します。弊社のNewValidDumps商品を安心に選択してNewValidDumps試験に100%合格しましょう。

正しい方法は大切です。我々NewValidDumpsは一番効果的な方法を探してあなたにCiscoの350-401学習教材試験に合格させます。弊社のCiscoの350-401学習教材ソフトを購入するのを決めるとき、我々は各方面であなたに保障を提供します。

Cisco 350-401学習教材 - 自分の幸せは自分で作るものだと思われます。

Ciscoの350-401学習教材認定試験は競争が激しい今のIT業界中でいよいよ人気があって、受験者が増え一方で難度が低くなくて結局専門知識と情報技術能力の要求が高い試験なので、普通の人がCisco認証試験に合格するのが必要な時間とエネルギーをかからなければなりません。

あなたは弊社の高品質Cisco　350-401学習教材試験資料を利用して、一回に試験に合格します。NewValidDumpsのCisco　350-401学習教材問題集は専門家たちが数年間で過去のデータから分析して作成されて、試験にカバーする範囲は広くて、受験生の皆様のお金と時間を節約します。

350-401 PDF DEMO:

QUESTION NO: 1
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 2
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 4
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 5
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D

SAP C_ACT_2403 - 良い対応性の訓練が必要で、NewValidDumps の問題集をお勧めます。 努力すれば報われますなので、Cisco　Cisco 350-401資格認定を取得して自分の生活状況を改善できます。 Snowflake SnowPro-Core-JPN - あなたがほしいものを得ることができますから、ミスしないだけで後悔しないです。 多分、Huawei H23-211_V1.0テスト質問の数が伝統的な問題の数倍である。 Oracle 1z0-076 - 例外がないです。

Updated: May 28, 2022